manualshive.com logo in svg

Garudan GF-1115-147 LM, User Manual, Page: 22 / 78

Share
Download
Garudan GF-1115-147 LM User Manual Download Page 22

 

 

© ANITA

 

 
MP04700EN_200120 

GF-1115-147 LM, GF-1115-447 MH 

22 

 

Adjusting the presser foot pressure 

 

 

 
Caution:

 

Turn off the main switch before the operation

.

 

 

 

1. Correct pressure of presser foot is important for correct feeding of the material. Insufficient 
pressure can result in slipping of the material and loss of constant stitch length. When accelerated, 
the stitch length is too short because the material is not properly pressed and slips between the 
presser foot and feed dog. If the pressure is too high, the material can be creased. Loosen the nut 

②.

 By turning the screw 

①

 clockwise 

Ⓐ

 the pressure is increased, by turning the screw counter-

clockwise the pressure is decreased. After adjustment, tighten the nut 

②

. 

 
2. Tip for correct adjustment: loosen the screw 

① at maximum

, and insert material under the 

presser foot. Start sewing and hold the material back by hand slightly. If the machine is not feeding 
material, tighten the screw 

①

. Repeat this step until the material is correctly fed. Then tighten the 

screw 

①

 by nut 

②

. If you change material, it will be necessary to make new adjustment of the 

pressure. Every material has different adhesion and behaves differently when being stitched. 
 

 

 

www.garudan.cz

Summary of Contents for GF-1115-147 LM















































































Reviews:

No comments