GARO LS4 43kW Installation Manual Download Page 9

Connect the charging cable to the EV.  
If authorization is activated, please hold a valid RFID-tag against the RFID reader on the side of the LS4 you want to use or use the 
operator app to authorize charging. 
Charging will start instant if the EV is ready for charging. See your EV charging manual.
When finishing charging, follow the EV’s instructions. 
After charging: Release the charging cable from your EV and place the charging cable at designated place. 

Firm

No car connected

Charging station available and ready for charging

Car connected

State B: Car connected but not yet ready for charging

Car connected

State C: Car connected and ready for charging, but charging 
station requires authentication to start charging (Free Charging = 
"OFF").

Blinking (3 blinks)

When car connects

The charging station detects that the cable is connected, but is 
yet to detect the car.

Blinking (30 

second blink)

Whenever during operation

Charging station have received command from backend to start 
charging and is waiting for car to connect.

Firm

Car connected

Charging is ongoing (state C)

Car connected

Charging is paused (state B)

Blinking

Whenever during operation

Charging station/point is reserved for a specific user

Firm

Whenever during operation

DC fault monitor may be defect.

Whenever during charging

Residual Circuit Current Breaker (RCCB) triggered.

Whenever during charging

DC fault detected.

Whenever during charging

Circuit breaker (MCB) triggered - Overload / short circuit

Whenever during charging

Type 2 connector motor locking was released/unlocked (the 
cable can be removed)

When connecting car

The socket outlet can not engage locking mechanism to lock the 
connector.

When connecting car

Charging cable is damaged.

Firm (3 seconds)

When RFID is presented

RFID card is not valid or not approved by backend.

Blinking

Whenever during operation

Charging station/point is deactivated. 

Blinking

When RFID is presented

Charging station is verifying the RFID in backend cloud service.

LED light indication When

Cause of error

USER INSTRUCTIONS

NORMAL USE

9

EN

Summary of Contents for LS4 43kW























Reviews: