GARO LS4 43kW Installation Manual Download Page 17

TECHNICAL SPECIFICATIONS

Product type

LS4 43kW

Standards / Directives

IEC 61851-1 and IEC 61439-7

 

EMC Classification:

2014/30/EU

Installation method:

Ground 

Installation environment:

Indoor / Outdoor

Location type:

Non-restricted Access

Rated Voltage:

3-phase 400VAC 50Hz

Rated Current (configurable)                              63A, 32A 1-phase or 3-phase
Installation systems:

TT, TN and IT* systems

Charging type:

Mode 3

Charging method

AC Charging

Protection class:

IP54

Mechanical impact resistance:

IK10

Temperature range:

 -25C - +40C

Weight:

40kg

Standard cable length (fixed cable version):

Standard 7.5m

Rated current withstand

10kA

Rated short-time withstand current

10kA

Rated conditional short-circuit current of an assembly

10kA

Short-circuit protective device type

Type C

Rated impulse withstand voltage 

4kV

Rated insulation voltage 

230/400V

Rated current of each circuit

63A

Rated diversity factor 

RDF=1

Pollution degree:

3

EMC environmental condition

A and B

RFID Frequency Band

13.56MHz

RFID output power

250mW

SERVICE INFORMATION

Care and maintenance GARO charging station LS4:
The warranty will only remain valid if service is performed.
Service is performed once a year and must be documented.
General authorization EL is required to perform service, i.e. only a 
qualified electrical contractor should perform the
service. The service is performed by inspecting the charging 
station’s exterior and interior parts, manipulating
components and conducting a functional inspection.
If the charging station is connected to a web portal or otherwise 
controlled from an external system via a service

provider, the service personnel must contact the service provider 
before a scheduled service. This is to be able to carry
out all steps in the service, but also to avoid automatic error 
reports being sent from the charging station when service
starts that may lead to other service personnel being called out at 
great expense. Normally the instructions for the
charging station indicate whether it is connected to a superior 
service.
If you have questions about service or a need for service, please 
contact your GARO retailer.

TECHNICAL SPECIFICATIONS

17

EN

Summary of Contents for LS4 43kW























Reviews: