background image

Universal dimmer actuators GDA2K-400 KNX / GDA4K-400 KNX

 

 

 

pdated: Mai-17 (Subject to changes)                                                                                                  Page 42 of 63  

 

4  APPENDIX  

 

4.1  Use of the soft switch function 

 

4.1.1  General 

 
The Soft switch function is a cycle consisting of switch-on, dimming up,  
Maintain target brightness, dimming down and switch-off. 
 

4.1.2  Soft ON for staircase lighting 

 
The following function is recommended for staircase lighting: 
When the light switch is operated: Full brightness. 
After required length of time: Lighting is slowly dimmed down and then switched off. 
 
 

0 %

t(h)

100 %

A/B

t1 = 0s

t3

t2 / t2+

Min.

Val.

C

D

P

 

 
 

 

Button sends 

Soft ON 

telegram. 

t1 

The 

Soft ON

 time is equal to 0, i.e. the "Dim up slowly" function is deactivated 

The brightness is immediately adjusted to the configured value after 

Soft ON

 

t2 

Configured time between 

Soft ON

 and 

Soft OFF

11

 elapses  

t2+  It is possible for t2 to be extended with another 

Soft ON

 telegram 

t2 or t2+ has elapsed, or a 

Soft OFF

 telegram was received:  

Start of the 

Soft OFF

 phase 

t3 

The brightness is gradually reduced within the configured time for 

Soft OFF

 

t3 has elapsed, the configured 

minimum brightness

 has been reached and the system dims to 0%  

 
 
The light can be turned off with a Soft OFF telegram or  
retriggered with a Soft ON telegram. 

                                                 

11

 

Soft Off 

via configured time or via 

Soft Off

 telegram.

 

Summary of Contents for GBO-300
































































Reviews: