GARO GBO-300 Manual Download

Page: 42 / 63

Universal dimmer actuators GDA2K-400 KNX / GDA4K-400 KNX

pdated: Mai-17 (Subject to changes) Page 42 of 63

4 APPENDIX

4.1 Use of the soft switch function

4.1.1 General

The Soft switch function is a cycle consisting of switch-on, dimming up,
Maintain target brightness, dimming down and switch-off.

4.1.2 Soft ON for staircase lighting

The following function is recommended for staircase lighting:
When the light switch is operated: Full brightness.
After required length of time: Lighting is slowly dimmed down and then switched off.

0 %

t(h)

100 %

A/B

t1 = 0s

t2 / t2+

Min.

Val.

Button sends

Soft ON

telegram.

The

Soft ON

time is equal to 0, i.e. the "Dim up slowly" function is deactivated

The brightness is immediately adjusted to the configured value after

Soft ON

Configured time between

Soft ON

and

Soft OFF

elapses

t2+ It is possible for t2 to be extended with another

Soft ON

t2 or t2+ has elapsed, or a

Soft OFF

telegram was received:

Start of the

Soft OFF

phase

The brightness is gradually reduced within the configured time for

Soft OFF

t3 has elapsed, the configured

minimum brightness

has been reached and the system dims to 0%

The light can be turned off with a Soft OFF telegram or
retriggered with a Soft ON telegram.

Soft Off

via configured time or via

Soft Off

telegram.

Summary of Contents for GBO-300
































































Search results

Summary of Contents for GBO-300

Reviews:

Related manuals for GBO-300

Brands by name

Popular brands

GARO GBO-300, Manual

Search results

Summary of Contents for GBO-300

Reviews:

Related manuals for GBO-300

Brands by name

Popular brands