background image

1. 

Plug in A/C D/C adapter at D/C input jack (8) (see figure 2). Use only approved 
adapters.

 

 

Batteries installation 

1.  Open battery compartment (9) on the back of the unit. (see figure 2) 
2.  Install / replace with 2x “AAA” size batteries in the compartment. It is 

recommended that only alkaline batteries are used. 

3.  Replace the battery compartment (9) on the back of the unit. 
4.  A short beep will be heard to confirm proper installation of batteries. 
5.  It will take approximately 3 seconds for the screen to light up. 

6.

 

Replace batteries when this symbol 

 is shown. This indicates low batteries.

  

 
Batteries safety warnings: 

1.  Please read all instructions carefully before use. 
2.  Install batteries correctly by matching the polarities (+/-). 
3.  Always replace a complete set of batteries. 
4.  Never mix used and new batteries. 
5.  Remove exhausted batteries immediately. 
6.  Remove batteries when not in use. 
7.  Do not recharge and do not dispose of batteries in fire as the batteries may 

explode. 

8.  Ensure batteries are stored away from metal objects as contact may cause a 

short circuit. 

9.  Avoid exposing batteries to temperature or humidity extremes or direct sunlight. 
10. Keep all batteries out of reach from children. They are a choking hazard. 
11. Please retain packaging for future reference. 

 
Setting up the weather station: 

The weather station will sound once batteries are installed or ac adapter is plugged in.  

1.  The double digits of sea level on the bottom left hand corner of the display will 

flash. Press 

+ / °C / °F

 button (2) or 

- / RCC

 button (3) to change the 

sea level closest to your location. The sea level units are in meters (1 meter 
equals approximately 3.28 feet). Contact your local weather bureaus or 
authorities for more information.  

2.  Press “HISTORY” button (5) to confirm sea level.  
3. Press 

+ / °C / °F

 button (2) or 

- / RCC

 button (3) to change the current 

weather situation of your location. See figure 3 below for the weather pattern that 
is resembles your immediate area. 

 

 

Summary of Contents for ND5010









Reviews: