Garmin GPSMAP 198C Owner'S Manual Download Page 75

Page: 75 / 126

GPSMAP 198C Sounder Owner’s Manual

AIN

ENU

YSTM

Systm (System) Tab

The System tab controls system setting for beeper, speed ﬁlter,

languages, system mode, and simulator controls, restores factory

settings, shows software version, and prepares software update

cards.

The following settings are available:
•

Beeper

—Off, Alarms Only, Key and Alarm: controls audible

beeps for keys and alarms.

•

Speed Filter

—Off, Auto, On: averages speed-readings.

•

Language

—shows the on-screen languages.

•

System Mode

—sets Normal or Simulator Mode.

•

Set Position

*—sets your location while in Simulator Mode.

See page

for additional instructions.

•

Track Control

*—Auto Track, User Track: controls your

heading in Simulator Mode.

•

Track

*—sets your heading in Simulator Mode.

•

Speed

*—sets your speed in Simulator Mode.

•

Transducer

*—sets a transducer type.

* These ﬁelds are only available when the unit is in Simulator

Mode.

The following options are also available from the Systm tab:

•

System Information

—shows the unit’s software, basemap

version, and electronic serial number.

•

Prepare SW Update Card

—prepares a data card to accept

software updates from your computer through the data card

programmer.

Press

MENU

for the following options:

•

Defaults

—restores settings on Systm page to default values.

•

All Unit Defaults

—restores all settings to Garmin’s original

setup values for the entire unit.

Summary of Contents for GPSMAP 198C































































































































Search results

Summary of Contents for GPSMAP 198C

Reviews:

Related manuals for GPSMAP 198C

Brands by name

Popular brands

Garmin GPSMAP 198C, Owner'S Manual

Search results

Summary of Contents for GPSMAP 198C

Reviews:

Related manuals for GPSMAP 198C

Brands by name

Popular brands