Garmin GPSMAP 198C Owner'S Manual Download Page 9

Page: 9 / 126

GPSMAP 198C Sounder Owner’s Manual

ASIC

PERATION

IMULATOR

ODE

Simulator Mode

Simulator Mode turns the GPS receiver off for use indoors or

practice. Any of the functions discussed in the following pages

can be performed in Simulator Mode. While in Simulator Mode, a

“Running Simulator” message appears after 2 minutes of inactivity.

Keep in mind that the GPSMAP 198C Sounder does not track

satellites in Simulator Mode, and this mode should never be

used for actual navigation. All the waypoint and route planning

completed in Simulator Mode is retained in memory for future use.

WARNING:

Do not attempt to navigate using Simulator Mode.

When the unit is set to Simulator Mode, the GPS receiver is

turned off. Any satellite signal strength bars shown are only

simulations and do not represent the strength of actual satellite

signals.

To place the GPSMAP 198C Sounder in

Simulator Mode:

1. Press

MENU

twice to show the Main Menu. Press up or

down on the

ROCKER

until the

GPS

tab is highlighted, and

then press

MENU

once.

2. Use the

ROCKER

to highlight

Start Simulator

, and press

ENTER

. Choose

to the retail demonstration, and press

ENTER

3. Press

ENTER

to conﬁrm the

Running Simulator

message

that appears at the bottom of the screen. “Simulating”

appears at the top of each of the Main Pages.

4. To turn off the Simulator Mode, press

MENU

, and select

Stop Simulator

Summary of Contents for GPSMAP 198C































































































































Search results

Summary of Contents for GPSMAP 198C

Reviews:

Related manuals for GPSMAP 198C

Brands by name

Popular brands

Garmin GPSMAP 198C, Owner'S Manual

Search results

Summary of Contents for GPSMAP 198C

Reviews:

Related manuals for GPSMAP 198C

Brands by name

Popular brands