background image

Rate of Turn Command Dial

The turn rate command is 

activated by a single press of 

the directional control dial. 

A single centered vertical 

bar will indicate the mode is 

active.  See Figure 18

Figure 18

The  “Rate  of  Turn  Command  Dial”  on  the  display  controls  the 

boat somewhat like your steering wheel at the helm.  Turning the 

dial either clockwise or counterclockwise will cause the autopilot 

to execute a turn and make a continuous rate of turn until the dial 

is  turned in  the opposite  direction until only  a  single  vertical bar 

is displayed.  As you continue to turn the dial, more vertical bars 

display, and the rate of turn will execute more quickly. 

Example: With two vertical bars to the right showing on the display 

would be like turning the wheel at the helm to about the 2 o’clock 

position and holding it there.     

You can take control of the boat at any time just by pressing and 

releasing  either  straight  arrow  on  the  handheld  or  grabbing  the 

wheel at the helm and turning it in any direction. Steering from the 

helm  will  cause  the  Shadow  Drive  to  temporarily  dis-engage  the 

autopilot, and the Rate of Turn command will drop out. When the 

boat is steered on a steady course, the autopilot will re-engage in 

heading hold mode.  You will need to press the Rate of Turn Dial 

again to activate the turn rate command.

Page 10

Summary of Contents for Gladiator TR-1














Reviews: