background image

9

GHP 10 Marine Autopilot System Installation Instructions

Hydraulic Considerations – 2.0 L and 1.2 L Pumps

Different boats have different hydraulic considerations you must examine before mounting the pump or disconnecting any hoses. 

Before starting the hydraulic installation, verify the type of hydraulic steering in your boat, and where to install the appropriate type of 

pump.

Notice

If the hydraulic steering of your boat does not match the hydraulic layouts in this manual, contact Garmin Product Support.

2.0 L or 1.2 L Pump Hydraulic Layout on Single-Helm Boats (without Power Assist)

notes:

2.0 L/1.2 L pump (and motor):

An unbalanced cylinder requires an 

unbalanced valve on the pump (

page 21

)

Mount the pump horizontally if possible. Do 

not mount the pump vertically with the pump 

end (hydraulic connections) down.

Shadow Drive:

Mount the Shadow Drive horizontally and as 

level as possible.

Install the Shadow Drive in either the port or 

the starboard hydraulic steering line.
Always install a length of hose between the 

helm and the Shadow Drive.

Do not install the Shadow Drive directly to 

the helm.

Install the Shadow Drive between the pump 

and the helm.

Do not install the Shadow Drive between 

the pump and the cylinder.

Balanced cylinder

Port fitting

Starboard fitting

.0 L/1. L pump 

(and motor)

Port line

Return line

Starboard line

Shadow Drive

Helm

P

R

S

Notice

Do not turn the system on until you bleed all the air from the helm, the Shadow Drive, the pump, and all the hydraulic lines. 

 

See 

page 34

.

Summary of Contents for GHP 10

















































Reviews: