background image

© 2010 Garmin Ltd. or its subsidiaries
All rights reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or stored in any storage 

medium, for any purpose without the express prior written consent of Garmin. Garmin hereby grants permission to download a single copy of this manual onto a hard drive 

or other electronic storage medium to be viewed and to print one copy of this manual or of any revision hereto, provided that such electronic or printed copy of this manual 

must contain the complete text of this copyright notice and provided further that any unauthorized commercial distribution of this manual or any revision hereto is strictly 

prohibited.
Information in this document is subject to change without notice. Garmin reserves the right to change or improve its products and to make changes in the content without 

obligation to notify any person or organization of such changes or improvements. Visit the Garmin Web site (

www.garmin.com

) for current updates and supplemental 

information concerning the use and operation of this and other Garmin products.
Garmin

®

, the Garmin logo, and GPSMAP

®

 are registered trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. GHP

, GHC

myGarmin

, and Shadow Drive

™ 

are trademarks of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin. Mercury

®

 

Verado

®

 is a registered trademark of the Brunswick Corporation. NMEA 2000

®

 is a registered trademark of the National Marine Electronics Association. Loctite

®

 and Pro 

Lock Tight

®

 are registered trademarks of Henkel Corporation.

For the latest free software updates (excluding map data) throughout the life of your  

Garmin products, visit the Garmin Web site at www.garmin.com.

© 2010 Garmin Ltd. or its subsidiaries

Garmin International, Inc. 

1200 East 151

st

 Street, Olathe, Kansas 66062, USA

Garmin (Europe) Ltd. 

Liberty House, Hounsdown Business Park, Southampton, Hampshire, SO40 9LR UK

Garmin Corporation

 

No. 68, Jangshu 2

nd

 Road, Sijhih, Taipei County, Taiwan

www.garmin.com

February 2010 

Part Number 190-01166-02 Rev. B 

Printed in Taiwan

Summary of Contents for GHP 10

















































Reviews: