background image

 Installation Planning and Considerations

190-01810-00

GDL 82 TSO Installation Manual

Rev. 5

Page 4-4

4.4   Antenna Requirements

4.4.1   L-Band Antenna

NOTE

Certain types of transponder antennas with thin radiator elements are intended for use at 1030 and 
1090 MHz. Evaluate these antennas on a model-by-model basis to determine their suitability as UAT 
data link antennas.

The GDL 82 requires the existing L-Band Ultra-High Frequency (UHF) antenna(s) meet the following specifications:

Standard 50 ohm vertically polarized antenna with a VSWR < 1.7:1 at 978 MHz and < 1.5:1 at 1090 MHz.

TSO-C66( ), TSO-C74( ), or TSO-C112( ) antennas that also meet the VSWR specification.

The antenna location should be:

1.

Away from major protrusions.

2.

As far away as practical from openings that can affect the radiation pattern (e.g., landing gear doors, access 
doors, etc.).

3.

At least 20 inches from any other transponder, TAS/TCAS, DME, or 1030/1090 MHz antennas.

Table 4-2   Acceptable L-Band Antennas

[1] Not recommended for new installations.

MANUFACTURER

PART NUMBER

MODEL/

DESCRIPTION

CONNECTOR 

TYPE

NOTES

Aero Antenna

AT130-16

DME Transponder

TNC

DC Grounded

Comant

CI-100 [1]

DME Transponder

BNC

Open Circuit

CI-100-2 [1]

DME Transponder

TNC

Open Circuit

CI-105 [1]

DME Transponder

BNC

Open Circuit

CI-105-3 [1]

DME Transponder

BNC

Open Circuit

CI-105-16 [1]

DME Transponder

BNC

Open Circuit

CI-110-40-30

DME Transponder

C

Open Circuit

CI-110-41-30

DME Transponder

C

DC Grounded

CI-110-60-30

DME Transponder

C

Open Circuit

CI-110-61-30

DME Transponder

C

DC Grounded

Dayton-Granger

L10-611-( )

L-Band Blade

Varies

DC Grounded

Garmin

590-0052 or 

 

013-00219-00 [1]

A-40

TNC

Open Circuit

590-0051 or

 

013-00174-00

A-41

TNC

DC Grounded

Summary of Contents for GDL 82





































































Reviews: