background image

AQUAMAP™ 10x2/12x2 SERIES

3

Dimensions and Ports (AQUAMAP 10x2 Series)

316.8 mm

185.2 mm

68.5 mm

1

2

3

4

5

6

7

8

9

Item

Usage

1

8-pin XDCR

2

LAN

3

Power

4

Ground

5

Video CVBS input - BNC

6

GPS antenna - BNC

7

HDMI video output

8

NMEA 0183

9

NMEA 2000

Dimensions and Ports (AQUAMAP 12x2 Series)

358.8 mm

226.8 mm

68.5 mm

1

2

3

4

5

6

7

8

9

Item

Description

1

8-pin XDCR

2

LAN

3

Power

4

Ground

5

Video CVBS input - BNC

6

GPS antenna - BNC

7

HDMI video output

8

NMEA 0183

9

NMEA 2000

Typical System Integration

NMEA 2000 

Network

Antenna

Radar

Panoptix

LAN

2nd AQUAMAP

Transducer

AQUAMAP

Camera

Monitor

Tools Needed

• 

Drill

   Bail mount: drill bits appropriate for the surface and hardware

  Flush mount: 14 mm (

9

/

16

 in.), 6 mm (

1

/

4

 in.) and 3.6 mm (

9

/

64

 in.) (with 

nut plate), or 3.2 mm (

1

/

8

 in.) drill bit (with no nut plate)

•  #2 Phillips screwdriver
•  Jigsaw or rotary tool
•  File and sandpaper
•  Marine sealant (recommended)

Mounting Considerations

NOTICE

This device should be mounted in a location that is not exposed to extreme 

temperatures or conditions. The temperature range for this device is listed in 

the product specifications. Extended exposure to temperatures exceeding the 

specified temperature range, in storage or operating conditions, may cause 

device failure. Extreme-temperature-induced damage and related conse

-

quences are not covered by the warranty.
When selecting a mounting location, you should observe these consider-

ations.

•  The location should provide optimal viewing as you operate your boat.
•  The location should allow for easy access to all device interfaces, such as 

the keypad, touchscreen, and card reader, if applicable.

•  The location must be strong enough to support the weight of the device 

and protect it from excessive vibration or shock.

•  To avoid interference with a magnetic compass, the device should not be 

installed closer to a compass than the compass-safe distance value listed 

in the product specifications.

•  The location must allow room for the routing and connection of all cables.
• 

The location must not be a flat, horizontal surface. The location should be 

in a vertical angle.

 

The location and viewing angle should be tested before you install the 

device. High viewing angles from above and below the display may result 

in a poor image.

Summary of Contents for AQUAMAP 10x2 Series











Reviews: