background image

Part # 4518084 Rev. 1 (09/04)

Page 11

OPERATING INSTRUCTIONS continued...

Diagnostics Mode

•  To  enter  Diagnostics  Mode,  press  and  hold  the 

Program (lower right blank) button for three, (3), 

seconds. When prompted, enter the code: 

3-4-2-

4

 using the buttons 1 – 0. Press “ENTER” (lower 

right blank).

 
•  After entering the code and pressing “ENTER,” the 

Moisture Plus Part Number will be displayed briefly 

and  then  the  display  will  change  to  Diagnostics 

Test – Buttonpad Test. Use the “YES” (upper right 

blank) and “NO” (Preheat Bread 425) buttons to 

scroll through the available diagnostic tests. Press 

“ENTER” to begin the desired test. 

 

  Buttonpad Test

 

1.  The display will show “Press the On/Off Button”. 

Upon pressing the On/Off button, the LED for the 

ON/OFF button will light briefly and then go out 

to show that the button works.

 
2.  The  display  will  then  prompt  the  user  to  press 

the  “TEMP”  button  (upper  right  blank).  After 

the user presses the “TEMP” (upper right blank) 

button, the corresponding LED will light to show 

the button works. The control will then continue 

to prompt the user to press the remaining control 

buttons. If the LED of the button pressed does not 

light, a buttonpad problem exists. After completing 

the Buttonpad Test, you will return to Diagnostics 

Mode. (Press “CANCEL” at any time during the 

test to return to Diagnostics Mode.)

  Door Switch Test

 
1.  After selecting Door Switch Test and pressing the 

“ENTER” (lower right blank) button, the display 

will show the position of each of the two switches. 

Open  and  close  the  door  slowly  to  verify  the 

operation of the door switches.

 

  Proper Door Switch Activation:

•  Starting  with  the  door  closed,  the  switches 

should read:

•  Slowly begin to open the door. Door switch 1 

should be the first to change states:

•  Next, door switch 2 should change state to:

•  If the switches do not operate as stated above, 

there is a problem with the door switches.

•  Press “CANCEL” to exit the Door Switch Test 

and return to Diagnostic Mode.

Summary of Contents for Moisture+ MPOE5L

















Reviews: