GB-12
To use the Pole Trimmer for trimming the bottoms and
sides of hedges and shrubs, hold the Pole Trimmer at the
positions as shown.
To use the Pole Trimmer for trimming low- lying foliage
or ground cover, hold the Pole Trimmer at the position
as shown.
Use the Pole Trimmer properly. Always wear eye protec-
tion, rubber gloves, and substantial foot wear while using
the Pole Trimmer. Always maintain proper footing and
balance and never overreach when using Pole Trimmer.
Before starting the Pole Trimmer, hold the unit with both
hands on the grip areas. Make sure that the cutter blade
is not touching anything.
Always keep the extension cord behind the Pole Trimmer
when in use. Do not drape the cord over the hedge where
it may be cut by the blades. Use smooth steady sweeping
motions to trim new growth. Do not try to cut too much at
one time. This can cause the Pole Trimmer to slow down
or get jammed, reducing the cutting efficiency.
Do not force the Pole Trimmer through dense growth. A
slight back and forth sawing action may ease the cutting
of larger, more dense growth. If the Pole Trimmer begins
to slow down, reduce the rate of speed at which you
are trying to cut. If the Pole Trimmer becomes jammed,
immediately turn Pole Trimmer off. Disconnect Pole
Trimmer from the power supply and remove the jammed
debris from the cutter blades.
Do not try to cut branches larger than 18mm in diameter.
For best results, trim the sides of hedges with an upward
sweeping motion. Trim the hedges so that the top is
slightly narrower than the bottom.
Cleaning, maintenance and storage of the pole
trimmer
WARNING:
Disconnect Pole Trimmer from power
supply before cleaning or servicing. Severe injury
or death could occur from fire, electrical shock, or
body contact with moving cutter blades.
WARNING:
When cleaning Pole Trimmer:
- Do not submerse Pole Trimmer in any liquids.
- Do not use products that contain Ammonia, Chlo-
rine, or abrasives.
- Do not use chlorinated cleaning solvents, Carbon
Tetrachloride, Kerosene, or Gasoline.
Use a soft cloth dampened with a mild soap and water
mixture to wipe Pole Trimmer pole, housing, and cutter
blades clean. Do not spray or pour water directly onto
Pole Trimmer.
• Keep cutting edge sharp and clean for best perfor-
mance and to reduce the risk of injury
• Follow instruction for lubricating and changing ac-
cessories.
• Inspect Pole Trimmer cord periodically, and if dam-
aged, have it repaired by an authorized service facility.
• Inspect extension cords periodically and replace if
damaged.
• Keep handles dry, clean, and free from oil and grease.
1. Check Damaged Parts
• If a part is damaged, carefully check the damaged
part before using the Pole Trimmer. Make sure the
part will operate properly and perform its intended
function.
• Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and any
other condition that may affect its operation.
2. When servicing Pole Trimmer, use only identical
replacement parts.
3. Store Idle Pole Trimmer Indoors.
When not in use, the Pole Trimmer should be stored
indoors in a dry location. Store Pole Trimmer above the
reach of children or in a locked area out of the reach of
children.
Summary of Contents for GHTI 50
