background image

5

Thermal

 

Overload

 

Protector

The compressor motor is equipped with a thermal overload protector. If the 

motor should overheat, the overload protector will shut the motor off. If this 

occurs, turn the on/off lever to the off position and allow motor to cool for 

approximately 5 minutes.

NOTE:

 Tank pressure must be below 100 PSIG for the compressor 

to start.

Restart  the  compressor  by  moving  on/off  lever  to  the  on  position.  If 

compressor fails to start, check for blown fuses; the compressor may require 

more time to cool. If the overload protector shuts down the motor frequently, 

it could be due to low voltage.Common signs of low voltage are:

1. Motor does not get up to power or speed.

2. Fuses or circuit breaker activate when starting compressor.

3. Lights dim or remain dim when compressor is started.

4. Other motor operated appliances fail to operate property.

5. Too many motor operated appliances on same circuit.

Pressure

 

Switch

The compressor is operated by an on - auto/off 

lever on the side of the pressure switch. By turning 

the lever to the “AUTO” position the compressor 

will start and stop automatically within the settings 

of the pressure switch. The pressure switch is 

factory adjusted to start the compressor when the 

tank pressure drops below 100 PSIG and to stop      Lever

when tank pressure reaches 125 PSIG. To stop the 

compressor, turn the lever clockwise to the “OFF” position. (DO NOT STOP 

THE COMPRESSOR BY REMOVING THE ELECTRICAL PLUG.) The on/off 

lever operates a valve which relieves pressure from the compressor. If the 

lever is left on when the electric power is interrupted, the compressor may 

have difficulty in starting under this pressure.

Operating

 

Procedures

1.  Make sure on/off lever is in the off position.

 WARNING:

 

Before using air tools or accessories, check manufacturer’s 

maximum pressure rating. Maximum pressure rating must be above 

125 PSIG.

2. Turn on/off lever to the on position and allow tank pressure to build.

3. When the motor stops, it has reached cutout pressure and the unit is 

ready for use.

NOTE:

 When using an accessory or air tool, pressure in the storage tank 

decreases. When it reaches a certain low level (cut-in pressure) the motor 

will automatically restart and raise the pressure in the storage tank.

4. To shut down compressor, simply move on/off lever to the off position.

5.  Allow compressor to cool.

6. Drain storage tank (see Storage Tank in Maintenance Section).

Summary of Contents for Thomas ULTRA AIR-PAC T-30HP

























Reviews: