background image

 

13-20-604   Page 46 

9.  Grease the O-Ring on the separator element and install the separator into the housing. 

 

10.  Replace the O-Ring between the minimum pressure/check valve and the air/oil separator housing. 

 

11.  Replace the sealing kit in the minimum pressure/check valve.  After the assembling of the valve, 

leave about .08 inch gap between the nut and the cover of the valve.  See “Changing Minimum 
Pressure/Check Valve Seals,” Section 4, page 28. 

 

12.  Install the minimum pressure/check valve assembly and tighten the bolts alternately for even 

tightness. 

 

13.  Open the air service valve. 

 

14.  Run the unit and check for leaks. 

 
 

COMPRESSOR OIL SYSTEM CHECK

 - The following readings are based on ambient temperature of 

80

°

 F (27

°

 C) with the system in good condition.  The compressor should be at operating temperature at 

the time of the checks.  One-half hour of loaded operation is usually sufficient to reach level-out operating 
temperatures. 
 

Air and Oil Discharge Temperature

 - 160

°

 F to 180

°

 F (71

°

 C to 82

°

 C) - Check with a thermometer at 

the discharge housing. 
 

Compressor Oil Inlet Temperature

 - 150

°

 F to 165

°

 F (66

°

 C to 74

°

 C) - Install a tee at the oil filter outlet 

and check with a thermometer. 
 

Oil Inlet Pressure

 - Check at the fitting in the line near the compressor oil inlet.  With air receiver 

pressure at 100 psi (6.9 bar), oil inlet pressure should be 80 to 90 psig (5.5 to 6.2 bar). 
 

Oil Cooler Oil Pressure Differential

 - Check differential across the oil system by measuring oil inlet 

pressure as described above. 
 

Oil Cooler Temperature Differential

 - The oil temperature differential depends on the temperature of the 

air at the oil cooler fan and cleanliness of the core faces.  As ambient temperatures and core restrictions 
increase, the oil cooler outlet temperature will increase.  The oil inlet temperature is approximately the 
same as the air discharge temperature. 
 

Summary of Contents for INTEGRA EFD99E





























































Reviews: