background image

 

13-8-638   Page 37 

 

SECTION 7 
BELT DRIVE

 

 
Proper drive belt tension and alignment are provided at the factory, however, good practice dictates 
checking the drive alignment and tension after shipment and before initial start-up. 

 

Sheaves should align straight across the front with a straight edge. The best tension is just enough 
tension to keep belts from “squealing” on start-up. 
 
 

CAUTION 

Excessive belt tension can damage the equipment.  Tension the belts as shown 
on Figure 7-1, page 39. 

 

 

REPLACING THE COMPRESSOR BELTS 

 
1. 

Disconnect, lockout and tagout the power supply to the starter. 

 
2. 

Remove the belt guards. 

 
3. 

Using adjusting screws, jack the motor base up to loosen the belt tension.  Remove the belts. 

 
4. 

Install new belts, tighten belts using the adjust screws.  Check for correct belt tension. 

 

5. 

Check sheave alignment.  (See “SHEAVE ALIGNMENT”). 

 
6. 

Assemble the guards. 

 
 
 

SHEAVE ALIGNMENT 
 

The sheave alignment and belt tightening system consists of a hinged plate for the motor which is 
supported between (2) posts and a slotted platform for the Tempest units.  To achieve proper sheave 
alignment the sheaves must be adjusted for both parallel and angular alignment.  The alignment between 
the motor and air-end sheaves should be confirmed with the use of a straight edge.  If the sheaves are 
properly aligned, the straight edge should touch the two outer edges of each sheave for a total of four 
points of contact.  Gaps between the outer edges of either of the sheaves and the straight edge indicate 
sheave misalignment. 

 
The airend sheave is set in the parallel and angular direction by mounting it on the air-end shaft that is 
part of the Tempest unit that is bolted to the platform.  The platform has been set in the parallel and 
angular directions by its inherent design.  The motor sheave is set in the parallel direction by sliding it on 
the motor shaft to position it in line with the airend sheave.  (Check for alignment with straight edge.)  

Note

: It may be necessary to loosen the Tempest unit and slide it in the platform mounting slots to keep 

the motor sheave fan blades in the correct position in the cooler orifice ring. 
 
The motor sheave is set in the angular direction by means of (2) jack bolts and the hinged plate.  To start 
the angular alignment process check to make sure the locking nuts on the jack bolts are loose.  The 
motor sheave can be aligned in the angular direction to the same plane as the airend sheave by turning 
down the jack bolts on one side or the other of the hinged plate.  (Check for alignment with straight edge.) 
It also may be necessary to use the nuts that are on the jack bolts to push up on one side or the other of 
the hinged plate.  Note: At this point it may also be necessary to make minor adjustments of the position 

Summary of Contents for INTEGRA EFD99B























































Reviews: