background image

 

13-8-620    Page 18 

WARNING 

Operation of the unit with improper relief valve setting can result in severe 
personal injury or machine damage.  Ensure properly set valves are installed 
and maintained. 

 

 

Figure 4-1 – CONTROL SCHEMATIC 

 

AIR CONTROL COMPONENTS

 - All units incorporate the following air control components.  See Figure 

4-1 for schematic tubing diagram. 
 

Inlet Valve

 - The inlet valve is a normally opened, pneumatically closed valve.  The inlet valve is 

controlled by a solenoid valve, which in turn is controlled by the AutoSentry T controller,  The inlet valve 
closes to unload the compressor and opens to load the compressor.  At shutdown the inlet valve closes to 
function as a check valve and to prevent the backflow of air and oil.  The seals will need to be replaced 
periodically.  The interval will depend on the environment and the operating conditions. 
 

Solenoid Valve

 (Figure 4-1) - The solenoid valve is operated by the controller.  When energized, the 

valve closes, the inlet valve opens and the package starts compressing air.  When the solenoid valve is 
de-energized, it closes the inlet valve and relieves the pressure in the reservoir. 
 

Minimum  Pressure/Check  Valve 

(Figure 5-4, page 30) - An internal spring-loaded minimum pressure 

valve is installed prior to the aftercooler to maintain a positive pressure on the oil system even when the 
air service valve is fully open.  This valve senses upstream pressure.  If demand for air exceeds the 
compressor capacity, the valve throttles the flow to maintain a minimum pressure on the upstream (oil 
reservoir) side of the valve.  When pressure rises above the minimum pressure (standard setting 40 to 45 
PSIG) the valve reaches the full open position. 
 
A check valve incorporated in the minimum pressure valve  prevents backflow of air from the shop air line 
when the unit stops, unloads or is shut down. 

302EBA797-C 
(Ref. Drawing) 

Summary of Contents for CHAMPION ROTORCHAMP EFB99B






















































Reviews: