background image

INSTALLATION, OPERATION, MAINTENANCE AND PARTS MANUAL

45 CFM / 150 PSIG HYDRAULIC-DRIVEN, OPEN 

CENTER & CLOSED CENTER, 12V & 24V, (OPTIONAL) 

COLD-WEATHER, ROTARY SCREW COMPRESSOR

Read this manual before 

installing, operating or 

servicing this equipment. 

Failure to comply with the 

operation and maintenance 

instructions in this manual 

WILL VOID THE EQUIPMENT 

WARRANTY.

NOTE

Use only Vanair Vanguard™ 

Premium Synthetic Oil and 

Genuine Vanair Parts. 

Inspect and replace 

damaged components 

before operation. 

Substituting non-Vanair oil 

or non-genuine Vanair filter 

components WILL VOID THE 

COMPRESSOR 

WARRANTY! 

NOTE

Making unauthorized 

modifications to the system 

components WILL VOID THE 

WARRANTY!

Always inform Vanair 

Manufacturing, Inc., before 

beginning any changes to 

the RS45 system.

KEEP THE MANUAL

WITH THE VEHICLE

NOTE

This publication contains the 

latest information available 

at the time of preparation. 

Every effort has been made 

to ensure accuracy.

Vanair Manufacturing, Inc. 
reserves the right to make 

design change modifications 

or improvements without 

prior notification.

Vanair Manufacturing, Inc.

10896 West 300 North

Michigan City, IN 46360

Telephone (toll free): (800) 526-8817

Service (toll free): (844) VAN-SERV

(844) 826-7378

Telephone: (219) 879-5100

Service Fax: (219) 879-5335

Parts Fax: (219) 879-5340

Sales Fax: (219) 879-5800

www.vanair.com

©2018 Vanair Manufacturing, Inc.

All rights reserved

P/N: 090126-OP_r0

Effective Date:

JANUARY-2018

Summary of Contents for Reliant RS45

























































































Reviews: