background image

 

13-8-620    Page 11 

 

INLET LINE LENGTHS 

 

 

Length of Inlet Line 

Diameter of Pipe Size 

0 to 10 Feet ............................................. Same as Compressor Inlet Opening 
10 to 17 Feet ........................................... One Size Larger Than Inlet Opening 
17 to 38 Feet ........................................... Two Sizes Larger Than Inlet Opening 

 
 

DISCHARGE SERVICE LINE

 - The discharge service line connection is made at the right hand corner of 

the package when viewed from the control box end, viewed from the oil cooler side.  A hand operated 
valve, (air service valve) must be installed between the unit and the customer’s air system.  If a fast 
operating valve such as a ball valve is used, it must be closed slowly to give the intake valve time to shut 
and keep the discharge pressure from spiking.  When manifolding two or more rotary screw units on the 
same line, each unit is isolated by the check valve in the unit discharge line.  If a rotary screw unit is 
manifolded to another compressor, be sure the other compressor has a check valve in the line between 
the machine and the manifold.  If a rotary screw and a reciprocating compressor are manifolded together, 
an air receiver must be located between the two units. 
 
 

DANGER 

Discharge air used for breathing will cause severe injury or death. 

 

Consult filtration specialists for additional filtration and treatment equipment to 
meet health and safety standards. 

 

 

ELECTRICAL WIRING

 - All of the electrical connections and controls are factory wired for the voltage 

specified on the order.  Verify that the available voltage source matches that shown on the compressor 
package nameplate before installing the compressor package.  It is necessary only to connect the 
package to the supply and ground of the branch circuit.  The connections to the compressor package are 
made with the electrical controls box, accessible by opening the cover of the box. 
 
The 24CA4820 Control Transformer (Cutler-Hammer C0250G6U) is connectable for a variety of input 
voltages.  Ensure that it is properly connected prior to applying power to the package.  Recommended 
connections are: 
 
 

Line Voltage 

Primary Connect 

Secondary Connect 

200-208 

H1 & H2 

X1 & X4 

230-240 

H1 & H2 

X1 & X3 

380-416 

H1 & H3 

X1 & X3 

460-480 

H1 & H4 

X1 & X3 

575-600 

H1 & H5 

X1 & X3 

 
 

WARNING 

Electrical shock can cause injury or death.  Open main disconnect switch, 
lockout and tagout before working on control box. 

 

 

Summary of Contents for CHAMPION ROTORCHAMP EFB99B






















































Reviews: