background image

 

 

Page 12

 

 

FLUID END (FIGURE 2-3) 
 
This  fluid  end  incorporates  the  traditional 
flange-mounted  fluid  end  design,  which 
simplifies installation and removal by simply 
removing  the  stay-rod  nuts.  These  stay-rod 
nuts must be made-up tight and remain tight 
during 

operation. 

(See 

Torque 

Requirements  on  page  34).    Plungers  are 
installed  and  removed  through  the  front 
suction  covers.      Plunger  packing  is 
accessible by removal of the packing nut or 
gland.    Plunger  packing  lube  holes  are 
provided in the fluid cylinder. 
 

The  EWS  Fluid  End  is  a  forged  alloy  steel 
block  is  designed  for  severe  applications. 
The  EWS  utilizes  heat-treated  “Ultima  1” 
Stem  Guided  Valves  to  provide  increased 
valve  life  and  improved  fluid  pass  through 
to  reduce  cavitation.  The  cross  bore 
intersections  are  hand  blended  and  hand 
polished  bore  to  reduce  surface  fatigue 
stresses.  The  Close  Flow  –  Drop  Hinge 
suction  manifold  works  directly  with  the 
Ultima  1  valves  and  fluid  end  design  to 
enhance  fluid  cylinder  loading  for  smother 
operations.  
 

 

 

FIGURE 2-3: C-2500Q Fluid End 

Summary of Contents for C2500Q QUINTUPLEX















































Reviews: