Gardner Denver 4500 Series, Parts List Operating And Service Manual

Page: 33 / 45

SB--7--626 Page 24
8” VERTICAL (Continued)
Size Size Size Size
Ref. No. 812 816 820 824
No. DESCRIPTION Req’d GDHA_C GDHB_C GDHC_C GDHD_C
* 37 LOCKWASHER (BEARING 16 95B3 95B3 95B3 95B3 . . . . . . . . . . . .
CARTRIDGE TO HEADPLATE)
* 38 SCREW--HX HD CAP/NYLOK 8 75A33N 75A33N 75A33N 75A33N . . . . . . . . .
(BEARING RETAINER TO
BEARING CARTRIDGE)
* 39 SCREW--SOC HD CAP/NYLOK 1 75P9N 75P9N 75P9N 75P9N . . . . . . . .
(OIL SLINGER)
40 SCREW--HX HD CAP 4 655EE040 655EE040 655EE040 655EE040 . . . . . . . . . . . . . . . .
(GEAR CASE TO HEADPLATE)
41 SCREW--HX HD CAP 4 655EE040 655EE040 655EE040 655EE040 . . . . . . . . . . . . . . . .
(DRIVE COVER TO HEADPLATE)
42 SCREW--HX HD CAP (BEARING 16 655ED070 655ED070 655ED070 655ED070 . . . . . .
CARTRIDGE TO HEADPLATE)
43 SCREW--SOC HD CAP (GEAR 10 75P58 75P58 75P58 75P58 . . . . . . . .
LOCKING CLAMP TO SHAFT)
44 SCREW--HX HD CAP 36 655EE180 655EE180 655EE180 655EE180 . . . . . . . . . . . . . . . .
(GEAR CASE,DRIVE COVER &
HEADPLATE TO IMPELLER CASE)
** 45 PLUG--SQ HD 4 64AA7 64AA7 64AA7 64AA7+ . . . . . . . . . . . . . . . . . . . . . . .
(HEADPLATE AIR VENT)
46 SPACER--GEAR 2 910612728908 910612728908 910612728908 910612728908 . . . . . . . . . . . . . . . . . . . . .
50 WASHER--PLAIN (BEARING 6 95U3 95U3 95U3 95U3 . . . . . . . . . .
CARTRIDGE TO HEADPLATE)
* KIT--OVERHAUL 0 200GDH6010 200GDH6010 200GDH6010 200GDH6010 . . . . . . . . . . . . . . . . . . . . .
KIT--OVERHAUL (GAS PUMP) 0 201GDH6010 201GDH6010 201GDH6010 201GDH6010 . . . . . . . . .
SHIM--IMPELLER CASE
ALUMINUM .010 THICK
}
910743080002 910743080002 910743080002 910743080002 . . . . . . . . . . .
ALUMINUM .005 THICK
}
910743080003 910743080003 910743080003 910743080003 . . . . . . . . . . .
ALUMINUM .002 THICK
}
300GDH732 300GDH732 300GDH732 300GDH732 . . . . . . . . . . .
ALUMINUM .003 THICK
}
301GDH732 301GDH732 301GDH732 301GDH732 . . . . . . . . . . .
ALUMINUM .004 THICK
}
200GDH732 200GDH732 200GDH732 200GDH732 . . . . . . . . . . .
* Included in Overhaul Kit.
** Gas Pump units only.
+ Not Shown.
++ Units built prior to 1983 utilized a 1” NPT Bull’s Eye type gauge -- part number 40L15. If replacing
a headplate, one each of Ref. Nos. 22 & 26 must also be included.
Ø Refer to Section D when replacing gears or rotors in an ”A” or ”B” version unit.
}
As required.