background image

 

Do not leave the mower out in the rain. The lawn must not be wet or very damp. 
 

 

Only push the mower at a normal walking pace. 
 

 

Be particularly careful when you change the direction of the mower or pull it 
towards you. Do not pulling it towards you while the blade is moving. 
 

 

Switch off the mower if it has to be pushed over surfaces other than grass, and 
when moving the mower to and from the area you wish to mow. 
 

 

Carefully actuate the starter switch in accordance with the instructions. (See 
Operating Instructions) 
 

 

Do not switch the mower on and off frequently over a short period of time, and in 
particular do not play with the ON/OFF switch. 
 

 

Do not touch the cutting blade until the machine has been disconnected from the 
mains and the cutting blade has reached a complete standstill. 
 

 

Never lift or carry the mower whilst the motor is running. 
 

 

Switch off the motor and disconnect the plug whenever you leave the lawn mower. 
 

 

Keep the lawn mower in a dry place which is inaccessible to children at all times. 
 

 

Before you adjust or clean the mower or check whether the mains lead is kinked or 
damaged, switch off the mower and disconnect the plug from the power supply. 
 

 

 

Summary of Contents for ME1030G






















Reviews: