•
Avoid engaging stones, piles of earth,
in the grass. If a large object is accidentally struck, if the cutting head gets blocked, overloaded or stringy
material gets wrapped in the cutting head: reduce the eng
cutting head has stopped rotating switch off the engine and remove the material.
•
Put the machine on the ground and check that the cutting head has not been damaged. If necessary, change
the cutting head. If the head is only
•
Always wear safety gloves for this operation and ensure the engine is switched off and the head is stationary.
•
When the 2 nylon cords become too short, accelerate the engine and bum
Automatically the 2 nylon cords will feed out and be cut to the correct length. Repeat the operation if
necessary.
ASSEMBLY OF THE PRUNER
ATTACHING THE PRUNING MECHANISM Fig 17
•
Remove the locating screw (5).
•
Using a 4mm Allen key, loosen the clamping bolt (4).
•
Slide the drive shaft (1) into the gearbox (2) until the locating hole (3) in the drive shaft is visible through the
locating hole in the gearbox (5).
•
Insert the locating screw (5) into the gearbox (2) and tighten.
•
Using a 4mm Allen key, tighten the clamping bolt (4).
Install the guide bar and the saw chain on the gearbox as follows
Fig 18
(1)
Guide bar
(2)
Saw chain
(3)
Gearbox
(4)
Sprocket
(5)
Chain tension adjust screw
(6)
Nut
(7)
Chain tensioner
(8)
Chain cover
The saw chain has very sharp edges. Use protective gloves for safety.
•
Loosen the nut 6, Fig 18/20 and remove the chain cover 8.
•
Mount the guide bar, then fit the saw chain around the bar and
sprocket Fig 19.
Pay attention to the correct direction of the saw chain Fig 19.
ngaging stones, piles of earth, small pieces of wood or anything that could be hidden or difficult to see
in the grass. If a large object is accidentally struck, if the cutting head gets blocked, overloaded or stringy
material gets wrapped in the cutting head: reduce the engine speed so the engine idles.
cutting head has stopped rotating switch off the engine and remove the material.
Put the machine on the ground and check that the cutting head has not been damaged. If necessary, change
the cutting head. If the head is only wrapped by vegetation, remove by hand and clean the cutting head
Always wear safety gloves for this operation and ensure the engine is switched off and the head is stationary.
When the 2 nylon cords become too short, accelerate the engine and bump the nylon head on the ground.
Automatically the 2 nylon cords will feed out and be cut to the correct length. Repeat the operation if
ATTACHING THE PRUNING MECHANISM Fig 17
y, loosen the clamping bolt (4).
Slide the drive shaft (1) into the gearbox (2) until the locating hole (3) in the drive shaft is visible through the
Insert the locating screw (5) into the gearbox (2) and tighten.
4mm Allen key, tighten the clamping bolt (4).
Install the guide bar and the saw chain on the gearbox as follows
:
Chain tension adjust screw
The saw chain has very sharp edges. Use protective gloves for safety.
Loosen the nut 6, Fig 18/20 and remove the chain cover 8.
Mount the guide bar, then fit the saw chain around the bar and
Pay attention to the correct direction of the saw chain Fig 19.
Fig 17
Fig 18
Fig 19
Fig 20
Fig 21
66
6
ieces of wood or anything that could be hidden or difficult to see
in the grass. If a large object is accidentally struck, if the cutting head gets blocked, overloaded or stringy
gine idles. Make sure that the
Put the machine on the ground and check that the cutting head has not been damaged. If necessary, change
wrapped by vegetation, remove by hand and clean the cutting head
Always wear safety gloves for this operation and ensure the engine is switched off and the head is stationary.
nylon head on the ground.
Automatically the 2 nylon cords will feed out and be cut to the correct length. Repeat the operation if
Slide the drive shaft (1) into the gearbox (2) until the locating hole (3) in the drive shaft is visible through the
88
8
