11
GB
10
GB
The additional filter can be installed as a pond edge controller for
adjusting water features and cleaning the filter housing from the
edge of the pond. Water is only drawn in via the additional filter.
You can connect the following hoses to the hose connection:
.
3 /4
”
and 1
”
for FP 750 E / FP 1000 E / FP 1400 E / FP 1800 E /
FP 2500 E
.
1 1/4
”
and 1 1/2
”
for FP 4000 E / FP 5000 E / FP 7500 E
For best results use a hose with the largest possible diameter.
1. Remove the cap
3
from the pump.
2. Press in snap fastenings
6
and
open up the filter housing
5
.
3. Push the hose connection
7
on to the pump.
4. Close filter housing
5
.
5. Insert hose connection
8
in
to one filter shell
4
and snap
into the second filter shell
4
.
6. Press sealing cover
3
on to
the pond edge control
4
.
7. Connect water feature pump
and pond edge control to a
hose.
4. Initial Operation
1. Place water feature pump on a firm base in such a way that the
filter housing
5
is completely covered by water.
2. Pull telescopic pipe
9
out to the desired length.
3. Netzstecker in eine Wechselstromsteckdose einstecken.
Warning: Pump will start immediately.
4. Set the quantity of water required for the water feature using the
regulator
0
.
5. Water bell : Screw insert into the water feature until the water
feature has produced the shape required.
TIP : Install the pond edge controller on a bed of gravel to
improve the water intake. The regulating valve
0
must be fully
open when using the pond edge controller.
1. Fill hose with water to remove any cushions of air in the hose.
2. Secure the pond edge controller at the edge of the pond (using
rocks, for example).
The pond edge control must be completely covered with water.
3. Set the quantity of water required for the water feature with the
regulator
A
.
Switch on water
feature pump :
Start pond edge control :
VARIANT 2 : Mount the pond
edge controller :
are people in the water. Swimming pools and
garden ponds should be designed according
to international and national design regulati-
ons.
v
Please consult a professional electrician.
For Austria :
Pumps for use on swimming pools and on
ponds may only be operated via an isolating
transformer.
v
Please consult a professional electrician.
For Switzerland :
In Switzerland mobile appliances which are
used outdoors, must be connected via a resi-
dual-current device.
Note :
Do not allow the pump to run without water
because dry-running leads to an undesira-
ble build up of heat.
Before operating the pump, look to see if there
is any damage of the pump (esp. regarding
power cable and plug). The connection cable
of the pump cannot be replaced. If the cable is
damaged the pump must be scrapped.
Do not use the power cable to carry the pump
or to pull the plug out of the socket. Protect
the power cable from heat, oil and sharp
edges.
The temperature of the liquid used must not
be below 4 °C or above 35 °C.
Sand and other abrasive substances in the
liquid cause increased wear and reduce the
output of the pump.
Please observe the local noise prevention
regulations.
All pumps
(a cascade
art. 7650
(b Waterbell
- 7654
(c jets of
water
art. 7655 - 7657
(d foaming -
spring
3. Assembly
To provide a firmer mounting, the filter housing can be attached to
a solid base (e.g. paving stone).
1. Screw nozzle pipe
1
on to the pump with the ball and socket
joint.
2. Screw the water feature insert you require (a / (b / (c / (d on
the nozzle pipe
1
.
2
Holder for GARDENA underwater light art 7951
The additional filter can be fitted on the filter housing to extend the
maintenance interval and to give the water feature a longer life.
1. Remove the cap
3
from the pump.
2. Fit both filter shells
4
on the filter housing
5
and clip into
place.
3. Press sealing cover
3
on to the additional filter
4
.
You can install additional filters
to increase the filter surface.
Additional filters are available from GARDENA Service.
Fit the pump :
VARIANT 1 : Mount the addi-
tional filter on the pump:
5
3
4
2
1
0
A
9
5
0
9
5
4
3
8
7
7
3
5
6
