background image

Battery

3V mod. CR2032

Channels

1/5

Encoding

RC Gaposa

Battery life

2 years

Frequency

434,15 MHz

Radiated power

0,150 mW

Protection rate

IP40

Coverage (int/ext)

65 ft / 656 ft

Working temperature

23°F / 104°F

TECHNICAL DETAILS

CAUTION

: Please don’t use these transmitters in areas with risks of radio 

disturbs over the norm (i.e. airports or radio repeaters). These transmitters 
may also be disturbed by telecommunication and/or transceiver systems 
with the same frequency.

NOTE

: If the LED doesn’t blink after the button pressure, then the battery 

has to be replaced.

The users manual or instruction manual for an intentional or unintentional remote control shall caution 
the user that changes or modifications not expressly approved by the party responsible for compliance 
could void the user’s authority to operate the equipment. In cases where the manual is provided only in 
a form other than paper, such as on a computer disk or over the Internet, the information required by 
this section may be included in the manual in that alternative form, provided the user can reasonably be 
expected to have the capability to access information in that form. 

Summary of Contents for Emitto Smart Line














Reviews: