Gantner GAT NET.Lock 7020 System Installation, Configuration & Operation Download Page 9

Page: 9 / 64

GAT NET.Lock 7020 System
Table of Contents

www.gantner.com

HB_GAT-NETLOCK7020--EN_12

TABLE OF CONTENTS

INTRODUCTION .......................................................................................................................................... 11

1.1

About this Manual ................................................................................................................................. 11

1.2

Chapter Overview ................................................................................................................................. 11

1.3

Contact & Enquiries .............................................................................................................................. 11

1.4

Target Group ......................................................................................................................................... 12

1.5

Formatting ............................................................................................................................................. 12

1.5.1

Safety-Critical Information ............................................................................................................. 12

1.5.2

Non-Safety-Critical Information ...................................................................................................... 12

1.5.3

Instructions and Results................................................................................................................. 12

GENERAL INFORMATION ......................................................................................................................... 13

2.1

Intended Use ......................................................................................................................................... 13

2.2

Unintended Use .................................................................................................................................... 13

2.3

Functional Description ........................................................................................................................... 13

2.4

Terminology .......................................................................................................................................... 15

2.5

RFID Technology .................................................................................................................................. 16

2.6

System Components ............................................................................................................................. 17

2.7

Order Information Guide ....................................................................................................................... 20

INSTALLATION ........................................................................................................................................... 21

3.1

Target Group ......................................................................................................................................... 21

3.2

Test Installation ..................................................................................................................................... 21

3.3

Metallic and Non-Metallic Doors ........................................................................................................... 22

3.4

Bolt Gauge ............................................................................................................................................ 22

3.5

Replacement After Break-In .................................................................................................................. 22

3.6

Door Status Function ............................................................................................................................ 23

3.7

Definition of the Door Hinge (Right or Left Door) .................................................................................. 23

3.8

Installation Requirements for the GAT NET.Lock 7020 and Bolt Set ................................................... 24

3.9

Measurement Diagrams for Installation ................................................................................................ 25

3.9.1

Door Width ..................................................................................................................................... 25

3.9.2

Dimensions of the GAT NET.Lock 7020 / GAT NET.Lock 7020 P ................................................ 25

3.9.3

Dimensions of the GAT NET.Lock 7020 USB and GAT NET.Lock 7020 USB P .......................... 26

3.9.4

Dimensions of the GAT NET.Lock BoltSet 7120 (Non-Metallic Doors) ......................................... 26

3.9.5

Dimensions of the GAT NET.Lock BoltSet 7220 (Metallic Doors) ................................................. 27

3.9.6

Dimensions of the GAT NET.Lock BoltSet 7320 (Glass Doors) .................................................... 27

3.10

Installation in Lockers with Non-Metallic Doors ................................................................................. 28

3.10.1

Installation Instructions for the GAT NET.Lock 7020 and Non-Metallic Doors .............................. 29

3.11

Installation in Lockers with Metallic Doors......................................................................................... 30

3.11.1

Cutouts in the Metallic Locker Door ............................................................................................... 31

3.11.2

Installation Instructions for the GAT NET.Lock 7020 and Metallic Doors ...................................... 32

3.12

Installation in Lockers with Glass Doors ............................................................................................ 33

3.12.1

Installation Instructions for the GAT NET.Lock 7020 and Glass Doors ......................................... 34

3.13

Installation of the GAT NET.Controller M/S 7020 ............................................................................. 35

3.13.1

Instructions for Mounting the GAT NET.Controller M 7020 and S 7020 ....................................... 35

ELECTRICAL CONNECTIONS ................................................................................................................... 37

4.1

Target Group ......................................................................................................................................... 37

4.2

System Structure ................................................................................................................................... 37

4.3

GAT NET.Lock 7020 ............................................................................................................................. 38

4.3.1

Power Supply ................................................................................................................................. 38

4.3.2

Connection Cable .......................................................................................................................... 38

Summary of Contents for GAT NET.Lock 7020 System

































































Search results

Summary of Contents for GAT NET.Lock 7020 System

Reviews:

Related manuals for GAT NET.Lock 7020 System

Brands by name

Popular brands

Gantner GAT NET.Lock 7020 System, Installation, Configuration & Operation

Search results

Summary of Contents for GAT NET.Lock 7020 System

Reviews:

Related manuals for GAT NET.Lock 7020 System

Brands by name

Popular brands