Gantner GAT NET.Lock 7020 System Installation, Configuration & Operation Download Page 28 | Manualshive

Page: 28 / 64

background image

GAT NET.Lock 7020 System

Installation

28

HB_GAT-NETLOCK7020--EN_12

www.gantner.com

3.10

Installation in Lockers with Non-Metallic Doors

For lockers with glass or plastic doors, see “3.12 Installation in Lockers with Glass Doors”.

The GAT NET.Lock 7020 can be installed on the left or right side of the inner locker wall depending on whether it is
a right or left-hinged locker door

(see “3.7. Definition of the Door Hinge (Right or Left Door)). The GAT NET.Lock Bolt

Set 7120 is installed on the inner side of the locker door. One drill hole is required in the locker door for the LED status
light. See Figure 3.9 and the following installation instructions.

1.  GAT NET.Lock 7020
2.  GAT NET.Lock Bolt Set 7120
3.  3 x mounting holes for the GAT NET.Lock 7020
4.  3 x mounting holes for the GAT NET.Lock BoltSet 7120
5.  Hole for LED

Figure 3.9 - Installation in a locker with non-metallic door (right-hinged)

«
...
26
27
28
29
30
...
»

Summary of Contents for GAT NET.Lock 7020 System

































































Reviews:

No comments

Related manuals for GAT NET.Lock 7020 System

Brand: WABCO Pages: 6

Brand: WABCO Pages: 6

Brand: Waferlock Pages: 2

Brand: Taymor Pages: 4

Brand: Philips Pages: 16

Brand: Coastal Pages: 14

Brand: GeoVision Pages: 3

Brand: Stock Loks Pages: 1

Brand: COMPX Pages: 1

Brand: Haifuan Pages: 10

Brand: Baldwin Pages: 2

Brand: veise Pages: 20

Brand: Creche Innovations Pages: 12

Brand: allgood Pages: 2

Brand: Abus Pages: 6

Brand: Velleman Pages: 2

Brand: Dormakaba Pages: 62

Timberline CB-232

Brand: COMPX Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands