background image

GAT ECO.Side Lock 7000 BA / NW BA 
Commissioning

 

www.gantner.com

 

HB_GAT-GAT-ECOSide-Lock7000-BA--EN_14

 

33

 

4

 

COMMISSIONING 

 

 

4.1  Target Group 

 

This chapter provides information for technicians responsible for putting the GAT ECO.Side Lock 7000 BA and NW BA into 

operation. A base knowledge of electronics is assumed. Previous knowledge of the GAT ECO.Side Lock 7000 BA / 

NW  BA  is  not  required.  Since  the  comissioning  process  is  identical  for  both  lock  variants,  the  general  term  GAT 

ECO.Side Lock 7000 BA is used. 

 

 

 

4.2  Power Supply 

 

 

 

Battery Information 

 

The GAT ECO.Side Lock 7000 BA 

is powered by one 3.6 V AA Lithium battery (see “8 TECHNICAL DATA”). 

The battery life span is designed around a defined number of locking cycles. The actual life span depends upon the 

number of locking cycles (usage frequency of the lock) and the environmental conditions. The battery must be 

replaced when the battery voltage becomes too low. If the battery becomes too weak, the locker can no longer be 

locked. The GAT ECO.Side Lock 7000 BA indicates a weak battery state with five red flashes of the LED and five 

acoustic signals during a locking attempt. 

 

NOTE!

 For optimal battery lifespan, use the approved battery available from GANTER (Part No. 914430) to 

power the GAT ECO.Side Lock 7000 BA. 

 

 

 

 

Inserting the Battery 

 

Before putting the GAT ECO.Side Lock 7000 BA into operation, the battery must be inserted into the battery 

compartment.  

 

NOTE! 

To avoid unnecessary battery usage, insert the battery directly before the GAT ECO.Side Lock 7000 

BA is installed. 

 

►  To access the battery compartment, remove the red battery cover (1 in Figure 4.1) on the underside of 

the housing by sliding a finger under the tab section of the battery cover. 

Summary of Contents for GAT ECO.Side Lock 7000 BA

































































Reviews: