background image

1

 ~ 

 

 

Picture of a Calibration Pan Held in Place By Sash Chains 
 

Using Calibration Pans: 

Place calibrations pans on spread-plate using the sash chains to hold them in place.   
Note: the 6-ft spreader only uses one pan all the others use two pans. 
Fill the spreader about half full.   
See chart below for size of spreader you have 6, 8, 10 or 12-Ft and mark out the distance to be 
traveled.  This distance equals 1/10 of an acre at the speed you with to travel. 
Pick the speed you what to go and travel the distance listed in chart below collecting the material in the 
calibration pans.   
Begin moving ahead of marked off distance so you are traveling at desired speed.   
Open bottom of spreader as the spreader passed the beginning of the marked off distance and then 
close the bottom as the spreader passes the end of the marked off distance.  
Weight material collected in pounds.   
Multiply this weight by 10 to get the applied rate in pounds per acre. 
Keep repeating this step until you get the rate you are looking for.   
Keep tract of the setting and speed traveled for future use. 
 
Your Spreader Width 

Distance to Travel to Collect 1/10 of an Acre. 

6-Ft Models 

726 Feet 

8-Ft Models 

544 Feet, 6-inches 

10-Ft Models 

435 Feet, 8-inches 

12-Ft Models 

363 Feet 

 
 

 
 
Know Area Method 

Fill hoper.  Treat a known area, such as an acre or two, and refill hopper to the same level, noting the 
quantity used.  Divide the amount required to refill by the area covered.  The result will be your actual 
application rate.  In necessary, adjust Cam-Gauge setting to increase or decrease amount being 
applied.  Recheck.  The following figures may help in your computations based on a filed length of 80 
rods (1320-Ft), or one-quarter mile. 
 
Your Spreader Width 

Portion of Acre Covered in One Round 

6-Ft 

6-Ft or .38 

8-Ft 

8-Ft or .50 

10-Ft 

10-Ft or .63 

12-Ft 

12-Ft or .75 

 
 
 
 

Summary of Contents for 10-Ft











Reviews: