background image

12

STRINGING  THE  FRAME

Getting Started

To begin stringing the main strings, thread 
the two ends of the string through the two 
center holes at the appropriate end of the 
frame  and  continue  through  the  opposite 
center holes. Thread one end of the string 
through the adjacent grommet hole and pull 
excess by hand.

Secure  one  of  the  strings  using  a  string 
clamp.

Pulling Tension

Wrap  the loose section of string once around 
the roller guide and insert the string between 
the diamond dust coated string gripper plates. 
Pull the string perpendicular to the gripper 
plates  while  slowly  rotating  the  tensioner 
crank clockwise until the brake lever pops 
out of the latching block. The string is now 
tensioned and can be clamped in place with 
the remaining fi xed clamp.

Repeat the above steps until all main strings 
are installed. Tie off ends of main strings at 
the appropriate hole as per racquet manu-
facturers specifi cations.

Clamping the First Main String

Secure the tensioned main string using the 
free fi xed clamp. Repeat the procedure for 
all of the remaining main strings and tie off 
following the racquet manufacturers recom-
mendations.

Follow  the  manufacturer’s  recommended 
stringing pattern for one or two piece stringing. 
This will determine the starting point for the 
cross strings. If applicable, tie the fi rst cross 
string using an appropriate starting knot.

Summary of Contents for 5003

























Reviews: