Gamma Dental Condylograph comfort Set Instruction Manual Download Page 37

Page: 37 / 60

Reference SL Articulator and Face Bow Systems

- 37 -

5.6

Eccentric articulator programming

Program set Reference SL

06-231310

(complete program set)

Composed of:

06-231321

TCI insert- black

(straight, retrusive open)
06-231322

TCI insert- white

(straight)
06-231323

TCI insert- yellow

(curve A

– slight curve)

06-231324

TCI insert- red

(curve B

–medium curve)

06-231325

TCI insert- blue

(curve C

– strong curve)

06-231331

SCI insert - white

(radius 18 mm, surtrusive open)
06-231332

SCI insert - yellow

(radius 18 mm, retrusive open)
06-231333

SCI insert - red

(radius 18 mm, detrusive open)
06-231334

SCI insert - blue

(straight, retrusive/surtrusive open)
06-231335

SCI insert - black

(radius 18 mm, retrusive locked)

06-231341

Protrusion stop

yellow (1 mm)
06-231342

Protrusion stop

red (2 mm)
06-231343

Protrusion stop

blue (3 mm)
06-231344

Protrusion stop

green (4 mm)
06-231345

Protrusion stop

black (5 mm)

Separately available:

06-231340

Protrusion stop set

orange (0.5 mm, 1.5 mm, and 2.5 mm)

06-231346

Protrusion stop set

white (6 mm, 7 mm, and 8 mm)

Summary of Contents for Condylograph comfort Set





























































Search results

Summary of Contents for Condylograph comfort Set

Reviews:

Related manuals for Condylograph comfort Set

Brands by name

Popular brands

Gamma Dental Condylograph comfort Set, Instruction Manual

Search results

Summary of Contents for Condylograph comfort Set

Reviews:

Related manuals for Condylograph comfort Set

Brands by name

Popular brands