background image

Instruction Manual : 

PLATFORM 2-MAN LADDER STAND

23

INSTALLATION AND USE INSTRUCTIONS

1.   With assembled product lying on the ground, 

position 

one person at bottom end of ladder lying on the 

ground.

 This person has to prevent the ladder end 

from tilting up when platform end is lifted and prevent 

the ladder from skidding across ground.

2.   a. Position two people at the platform end of the 

ladder, lift the platform end and continue uprighting 

by walking toward bottom end of ladder and moving 

hands along ladder legs. 

Stand ladder up against 

chosen straight tree on dry, level ground.

 Use 

caution when ladder comes over center against the 

tree. 

SEE FIGURE 15A.

 

b. Step back and look at the ladder top to see that it is 

level. Adjust as needed to achieve a level platform top. 

Make sure tree blade is contacting tree. 

SEE FIGURE 

15B.

 

c. Step down hard on bottom step to push ladder legs 

into the ground. 

SEE FIGURE 15C.

STEP 1

FIGURE 15

WARNING

Never

 use a treestand on a dead, leaning, diseased or 

loose barked tree, or a utility pole. 

Always

 avoid electrical  

power lines.
Bring ratchet strap(s) up with you in a pocket - 

Do Not

 

carry in your hands!

 

During installation and removal of ladder treestands, you 

must always and properly use the included Full Body Harness 

(Fall Arrest System). Refer to the Full Body Harness instructions 

included with this product for proper use.

3.  While two people hold the stand in place, the third 

person must connect the horizontal stabilizer bar 

to the tree. Adjust the length of the stabilizer bar 

as needed so it contacts the tree and is level to the 

ground. Then secure it to the tree with the 6’ cam strap 

(28) by forming a cinch knot with both ends of the 

strap and running the long end of the strap through 

the cam buckle. 

SEE FIGURES 16A AND 16B.

FIGURE 

16A

FIGURE 

16B

STEP 2

A

A

B

C

Summary of Contents for PL201GW





























Reviews: