background image

Explanation of Safety Signal Words

 

The safety signal word designates the degree or level of hazard seriousness.

 

 

DANGER

: Indicates an imminently hazardous situation which, if not avoided, will result in death or 

serious injury.

 

 

WARNING

: Indicates a potentially hazardous situation which, if not avoided, could result in death or 

serious injury.

 

 

CAUTION

: Indicates a potentially hazardous situation which, if not avoided, may result in minor or 

moderate injury.

 

 

CAUTION

: Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, 

may result in property damage.

 

 

 

Safety Precautions

 

WARNING: To prevent personal injury or equipment damage,

 

 

Study, understand, and follow all instructions before operating this device.

 

 

Wear eye protection that meets OSHA and ANSI Z87.1 standards.

 

 

Only qualified personnel shall perform inspections and repairs to this lift.

 

 

Before using lift, inspect the lift for bends, cracks, dents, elongated holes, or missing 

hardware. If damage is found, discontinue use.

 

 

Use only those repair parts called out in the parts list in this document. Items found 

in the parts list have been carefully tested and selected.

 

 

Do not exceed the rated capacity of lift or platform extension.

 

 

Do not raise or lower lift with platform extended.

 

 

Use only on a hard, level surface.

 

 

Do not raise or move a load having a center of gravity extending beyond the wheels. 

Tipping can result in personal injury.

 

 

Do not move lift while a load is raised. Carefully and slowly move the load on inclines 

or around corners.Tipping can result in personal injury. Lower load completely before 

storage.

 

 

Do not stand under a load supported by the lift.

 

 

Secure component in place before removing it from the lift.

 

 

No alterations shall be made to this product as this will void the warranty.

 

Pump

 

 

Do not exceed the hydraulic pressure rating noted on the pump data plate or tamper 

with the internal high pressure relief valve. Creating pressure beyond the rated 

pressure can result in personal injury.

 

 

Before replenishing the fluid level, retract the system to prevent overfilling the pump 

reservoir. An overfill can cause personal injury due to excess reservoir pressure 

created when cylinders are retracted.

 

 

 

 

 

 

 

Summary of Contents for BLP 1000















Reviews: