Gallien-Krueger MB200 Owner'S Manual Download Page 9

9

MB SERIES

Tech Talk 

Characteristics of the MB Series:

The  MB  Series    is  a  flexible,  state-of-the-art 

amplifier  designed  to  deliver  maximum 

performance  while  remaining  small,  lightweight 

and    simple  to  operate.  This  is  accomplished 

through a few, very important features: 

·Class D power supply and power amp.

·Four,  Bass  specific  bands  of  active 

equalization for precise tone control.

·Balanced direct output eliminates the need for 

a direct box.

·Continuously variable fan cooling. 

Equalization:

Standard tone controls and graphic equalizers give 

you  plenty  of  variation,  but  they  don’t  provide 

what  the  instrument  really  needs.  The  fact  is, 

graphic  equalizers  are  intended  for  room 

equalization. The equalization in Gallien-Krueger 

amplifiers  reflects  40  years  of  continuous 

development and refinement.

The GK equalizer is unique to the industry, it’s not 

just a normal four band equalizer, each section is a 

special  circuit  optimized  to  perform  a  Bass 

specific job in its range of operation. 

These sections are wired in series, so they add to 

one  another  creating  a  tremendously  flexible 

equalizer, that sounds natural at any setting. Now 

it is possible to obtain the sound you desire. 

Contour:

The Contour is used to completely revoice the amplifier. 

This control tunes between two different shaping circuits, 

with greatly different responses. With the control all the 

way  up,  the  low  end  is  slightly  boosted,  the  mids  are 

dropped and the high end is pushed up. This is only found 

in GK amplifiers.

Cool Running = Reliability:

To  cool  the  amp  when  its  being  driven  hard,  we’ve 

designed a temperature sensitive fan cooling system. When 

the amp is under a light load, the fan is off or running at a 

low speed, reducing fan noise. As the amp works harder, 

the fan speed increases to keep everything cool.

Smart Protection Circuitry: 

The MB Series protection circuitry constantly monitors for 

unsafe  operating  conditions  such  as  short  circuits, 

miss-wired  speaker  cables,  blown  speakers,  improper 

ventilation,  and  incorrect  speaker  configurations.  In 

addition, protection is provided during power up/down. If 

the MB Series senses any unsafe operating conditions, the 

output  signal  is  immediately  muted  and  the  power  light 

changes  from  Blue  to  Red.  The  amplifier  will  remain 

muted until the fault is removed. If the protection circuit 

activates while playing, turn the amplifier off and check 

the amplifier speaker output connections. Be sure that you 

are  not  exceeding  the  maximum  recommend  load 

described in this manual. If the problem persists, contact 

GK directly for technical advice. 

In Closing:

You should now have a thorough understanding of how 

your new MB Series amplifier works and what advantages 

it can offer you in getting “your” sound. We thank you for 

reading  the  Owner’s  Manual  and  wish  you  the  best  of 

times!  Please  send  us  your  comments  via 

www.gallien-krueger.com 

or 

email 

us 

at 

[email protected].

Summary of Contents for MB200











Reviews: