background image

 

- 20 -

                           

Two Year Warranty 

 

This new Galaxy radio is covered by a two year limited warranty. Here are the details. 

 

 

All of our Galaxy radio model numbers begin with the letters “DX” and are covered 
by our Limited Two Year Parts and Labor Warranty. 

 

 

“Limited” means that we will repair problems caused by factory defects or normal 
use at no charge. Work performed by qualified technicians which did not cause any 
damage to the radio will not void the warranty and will be left intact. Problems 
caused by unqualified technicians or operator abuse can also be repaired, but there 
will be a charge. 

 

 

The warranty period begins when the radio is first purchased. However, in the 
event that the dated sales receipt has been lost or the radio was purchased used, 
our radios are still covered for 26 months from the date of manufacture based on 
the serial number. Our warranty comes with the radio and remains valid even if 
you sell the radio to someone else. Refurbished radios are distinguished from new 
radios by using the letter “R” as the first character of the serial number. 

 
There are no off-site “Factory Authorized” service centers for Galaxy “DX” models. All 
warranty work must be done at our facility. 
 
For maximum convenience, these radios may be shipped directly to us for repair after 
obtaining a Repair Authorization Number (RAN). This RAN may be obtained from our 
website or by calling our Service Department at 760-480-8800 between 10:00 AM and 
4:00 PM Pacific Time. The RAN must be written below your return address on the 
outside of the shipping box. Boxes, which arrive without an RAN, will be refused, and 
the shipping company will return the unopened box to you. Be sure to have a pen and 
paper ready along with the serial number of your radio before calling. We will give you 
the RAN and our shipping address over the phone.  
 
When you send your radio, please include a copy of the sales receipt and a note with a 
detailed description of the symptoms, especially if they are intermittent. This will help 
our technicians locate the problem so we don’t waste time sending the radio back and 
forth. If possible, please include a daytime phone number in case our technicians have 
any questions. Do not send your bracket, power cord or microphone unless we ask you 
for these items during our phone conversation. 
 
You are responsible for getting the radio safely to us. (We suggest using United Parcel 
Service - UPS.) You must pay to ship the radio to us, and we will pay to ship the radio 
back to you. Since we use UPS and they do not ship to Post Offices boxes, please 
provide us with a street address for the return of your radio. Be sure to print clearly. 
 
We appreciate your choosing a Galaxy radio and we will make every effort to get you 
back on the air as soon as possible. 

 

Be sure to visit our web site at: 

www.GalaxyRadios.com. 

 

 

- 21 -

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Printed in Malaysia 

AT0949010V 

 

Summary of Contents for DX-939












Reviews: