GAI-Tronics IDA1000A Installation And Service Manual Download | Manualshive

Page: 12 / 25

background image

Pub. 43004-027B

Model IDA1000A DC Remote Adapter Installation and Service Manual

Page 12 of 24

P:\Radio Products-Current Release\43004\43004-027B\43004-027B.docx
06/18

Accessory Connections

Accessory connections are made to the 15-pin accessory connector, located on the rear of the unit.
Numeric designations and functions are parallel to the radio pin numbers and functions as described
above. Input and output signals are opposite those of the radio connections.

Line Connections

The landline RJ11/RJ14 connector to J1 is polarity sensitive. Wire the modular connector as follows:

N

OTE

:

RJ11 pins are labeled 2 through 5. Pin 2 is on the right-hand side looking into the modular

connector.



Pin 3 (dc control negative) and 4 (dc control positive) for TX/RX operation.



Pins 2 and 5 are not used on the RJ11 connector.

Radio connections are made via P1-1 to P1-15. J3-1 to J3-15 accessory connections correspond
numerically and functionally.

«
...
10
11
12
13
14
...
»

Summary of Contents for IDA1000A


























Reviews:

No comments

Related manuals for IDA1000A

Brand: Laird Pages: 46

Brand: Hi-flying Pages: 19

Brand: Shimano Pages: 39

Brand: Z-Com Pages: 46

Brand: TBI PRO Engineering Pages: 9

Brand: Batimex Pages: 2

Brand: Synapse Pages: 33

Brand: Origin Instruments Pages: 12

EZ Connect SMC2662W

Brand: SMC Networks Pages: 62

Brand: Logitech Pages: 143

Brand: JVC Pages: 44

FriendlyNET Home

Brand: Asante Pages: 4

Brand: nLight Pages: 2

SATASTAR series

Brand: NitroAV Pages: 5

Brand: ESI Pages: 4

Brand: PIEXX Pages: 2

Brand: AmbiCom Pages: 1

BT2-USB Class I

Brand: AmbiCom Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands