manualshive.com logo in svg

GAI-Tronics IDA1000A, Installation And Service Manual, Page: 8 / 25

Share
Download
GAI-Tronics IDA1000A Installation And Service Manual Download Page 8

Pub. 43004-027B 

Model IDA1000A DC Remote Adapter Installation and Service Manual 

Page 8 of 24 

P:\Radio Products-Current Release\43004\43004-027B\43004-027B.docx 
06/18 

Operation 

Operational Description 

The Model IDA1000A DC Remote Adapter is for use with base stations or repeaters controlled from a 
remote desk set or console by dc line currents.  One adapter can interface up to ten dc remote desk sets to 
the base station or repeater, depending on the system design. 

The Model IDA1000A incorporates all necessary circuit interfacing to translate single-frequency 
(5.5 mA) transmit and monitor (-2.5 mA) commands into signals to control base station operation.  Where 
applicable, F2 transmit (12.5 mA) commands are also supported when used with a two-frequency base 
station.  Frequency outputs are jumper-selectable for open collector, 5 V pull up, or pull down.  The 
Model IDA1000A can be programmed to revert to F1 or F2 receive after transmit (see Table 3). 

Monitor operation can be either latching or non-latching.  The adapter routes audio signals between the 
wire line and base station circuitry.  Transmit audio from the wire line is amplified before being input to 
the station.  Receiver audio from the base station is amplified before being output to the wire line. 

Five LED function indicators are included on the front panel.  When illuminated, they indicate wire line 
push-to-talk command, a monitor command, and presence of 5 V dc power.  Two LEDs indicate detection 
of line current levels of 5.5 mA (

F1

) or 12.5 mA (

F2

). 

Front Panel LED Operation 

The operation of the IDA1000A DC Remote Adapter front panel LEDs is as follows: 

PWR LED 

The 

PWR

 LED illuminates to indicate that the IDA1000A DC Remote Adapter dc power is on. 

PTT LED 

The push-to-talk LED, labeled 

PTT

, illuminates when a valid transmit request has been decoded. 

MON LED 

The timed or constant monitor LED, labeled 

MON

, illuminates when the IDA1000A is in the monitor 

mode, and indicates detection of a line current level of -2.5 mA. 

F2 LED 

The front panel 

F2

 LED indicates detection of line current level of 12.5 mA (F2).  It illuminates to 

indicate that the unit is programmed to use the F2 transmit (12.5 mA) command, which is supported when 
used with a two-frequency base station. 

F1 LED 

The front panel 

F1

 LED illuminates to indicate that the unit is programmed to translate the single-

frequency (5.5 mA) transmit command into signals to control base station operation.  The IDA1000A 
may be programmed to revert to F1 or F2 receive after transmit. 

Summary of Contents for IDA1000A


























Reviews:

No comments