Gaggenau VG415315SG, Instruction Manual

Page: 32 / 36

en
Important notes
Read these instructions carefully and keep them in a safe place.
Safety during use can only be ensured if the appliance is fitted
correctly according to these installation instructions. The installer is
responsible for ensuring that the appliance operates perfectly at the
point of installation.
Attention!
According to the Gas Safety Ordinance of Hong Kong, any gas
installation works including the installation of appliances and
connection tubing, must be undertaken by registered gas
installers who are registered for that appropriate classes and be
employed by registered gas contractors.
Use approved gas tubing bearing EMSD approval marking
(example : 機電工程 機電工程署批准 署批准 EMSD APPROVAL GTXXXX) for
connection to appliances or other appropriate methods
accepted by EMSD.
Appliance must not be converted to another type of gas.
Before carrying out any type of work, turn off the electricity and gas
supply.
For installation, currently applicable building regulations and the
regulations of local electricity and gas suppliers must be observed.
The operating pressure of this gas hob is 15 mbar. Therefore no
external gas governor is required.
Risk of gas escape!
After connecting the appliance to the gas supply, always check the
connection for leak tightness. The manufacturer accepts no
responsibility for the escape of gas from a gas connection which has
been previously tampered with.
Ensure sufficient air exchange in the room where the appliance
is installed. Up to11 kW total input:
■
Minimum volume of the room where appliance is installed: 20 m 3
■
A door leading to the open air or a window which can be opened.
Up to18 kW total input:
■
Minimum volume of the room where appliance is installed: 2 m 3
per kW total input.
■
A door leading to the open air or a window which can be opened.
■
An extraction hood into the open air. Minimum displacement
volume of extraction hood: 15 m 3 /h per kW total input.
The installation system must incorporate an all-pin isolating switch
with a contact opening of at least 3 mm, or the appliance should be
connected to the mains via a safety plug. The plug must remain
accessible after installation is complete.
Specifications on the rating plate showing voltage, type of gas and
gas pressure must agree with the local mains connection conditions.
Do not kink or trap the mains connection cable.
This appliance corresponds to appliance class 3 (for installation in a
kitchen unit). It must be fitted according to the installation drawing.
The wall behind the appliance must be made of nonflammable
material.
This appliance is not intended for operation with an external timer or
an external remote control.
Do not install this appliance on boats or in vehicles.
Special accessories
You can order the following special accessories from your specialist
dealer:
WP 400 001 Multi-layer material wok pan, with curved base and
handle, Ø36 cm, 6 litres volume, 10 cm high.
Only use the accessories as specified. The manufacturer accepts no
liability if these accessories are used incorrectly.
Preparing the units (Fig.1a)
The kitchen unit must be heat-resistant to at least 90 o C (about
190
o
F). The stability of the unit must be maintained after producing
the cut-out.
Produce the cut-out in the worktop for one or more Vario appliances
as shown in the installation sketch. The angle between the cut
surface and the worktop must be 90 o .
The cut edges at the sides must be flat to ensure a good fit of the
retaining springs on the appliance. In laminated worktops, it may be
necessary to fit strips at the sides of the cut-out.
Remove shavings after cutting. Seal cut surfaces for resistance to
heat and so they are watertight.
Pay attention to a minimum gap of 10 mm from the underside of the
appliance to kitchen units.
Use suitable base constructions to ensure load-carrying capacity
and stability, especially in the case of thin worktops. Pay attention to
the weight of the appliance, including any payload. Reinforcement
material used must be resistant to heat and moisture.
Note: Wait until the appliance has been installed in the installation
opening before checking that it is level.
Installation flush with surrounding surfaces (Fig. 1b)
It is possible to fit the appliance into a worktop such that it is flush
with the worktop surface.
The appliance can be installed in the following temperature- and
water-resistant worktops:
 Granite worktops
 Plastic worktops (e.g. Corian®)
 Solid wood worktops: Only on agreement with the worktop
manufacturer (seal the cut-out edges)
 For other worktop materials, contact the worktop
manufacturer about their use.
The appliance cannot be installed in compressed-wood worktops.
Note: All cut-outs in the worktop are to be carried out in a specialist
workshop in accordance with the installation diagram. Each cut-out
must be neat and precise as the cut edge is visible on the surface.
Clean and degrease the cut-out edges with a suitable cleaning agent
(follow the instructions from the silicone manufacturer).
Combining multiple Vario appliances (Fig.1c)
The connecting strip VA420004/010 is required in order to combine
multiple Vario appliances. This can be ordered separately as an
optional accessory. When making the cut-out, allow extra space for
the connecting strip between the appliances (see installation
instructions VA420004/010 ).
Appliances can also be fitted in their own individual cut-outs as long
as at least 50 mm of material is left between the cut-outs.
Combination with appliance cover (Fig.1d)
The appliance cover VA440010 is available separately as an
optional accessory. Take the additional space required by the
appliance cover into consideration when making the cut-out.
Hole for the control knob
Possible installation types:
 At the front of the floor cabinet
 In the worktop next to the appliance
 In the worktop in front of the appliance
Note: Follow the installation instructions provided for the control
knobs.
Fitting the control knobs (Fig.2)
Note: Follow the installation instructions provided for the control
knobs.
1. Depending on the distance between the control knobs, it may
be necessary to break off the retaining plate at the
perforation. Hold the retaining plate in place against the rear
of the control panel/ underside of the worktop or secure it in
place with the screws provided.
2. When fitting an individual control knob or if the retaining plate
has been broken off at the perforation, use two screws to hold
each retaining plate in place and prevent it from rotating.
For stone worktops, use temperature-resistant two-
component adhesive (for metal to stone) to adhere the
retaining plate.
3. Remove the protective film on the back of the illuminated ring.
4. Push the control knob into the hole, and use the installation
tool provided to tighten the nut at the rear.
5. Use the short cables provided to connect all the control
knobs. The male connectors must snap into place in the
female connectors.
Note: The two female cable connectors on the control knob
are identical.
6. Attach the long cable to one of the control knobs to connect it
to the appliance. The male connector must snap into place in
the female connector.
Note: The appliance can be connected to any control knob.
7. After fitting, check that all plug-in connections are seated
correctly.
8. After fitting all the cables, secure them to the retaining plate
by turning the tab down.