11
Rev 1/23
GB751SH INSTALLATION TOOL S/N: 1364 AND ABOVE
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
FILLING PROCEDURE
IMPORTANT:
Be sure to use thread sealant on all hydraulic fittings, Loctite® 545 or equivalent or a non
-
hardening Teflon® thread
compound such as Slic
-
tite®. Tighten until fitting feels snug and then continue to tighten 1/2 to 1 full turn.
CAUTION:
Over tightening
can easily distort the threads. DO NOT USE TEFLON® TAPE.
CAUTION:
Teflon® tape is an excellent thread sealer, however, if it is not
properly applied, pieces of Teflon® may enter the hydraulic system and cause a malfunction or damage.
1.
Put the piston rod wrench assembly (704149) into the top of handle assembly (744129), pushing down firmly until piston rod
assembly (744136) is completely in the down position.
2.
Fill oil passage and reservoir with Automatic Transmission Oil, Dexron® III or equivalent. The reservoir is the area surrounding
the
power cylinder (743131). When looking at the top of the handle assembly (744129), the oil passage is the hole that has a
counter bore for o
’
ring (S832). Do not overfill causing oil to go in air passage hole.
3.
Install gasket (704129), o
’
ring (S832), button head cap screws (A
-
928) and manifold
-
handle (744303) to handle assembly (744129)
keeping hydraulic hose (A
-
317) towards plug (704313).
4.
Push piston (751307) full forward. Install gasket (704129) and o
’
ring (S832) on handle assembly (700343). Assemble head cylinder
assembly (703119) to handle assembly (700343) using button head cap screws (402479). Apply Loctite® 242 to all cap screws and
torque to 40 inch lbs. (4.52 Nm).
5.
Coil tool hoses up on bench and lay handle assembly (744129) down on side so that the hole marked #4 on manifold handle (744303)
is to the top. Set head cylinder assembly (703119) over a small bucket or can. Completely fill up fill bottle (745263).
6.
Remove button head cap screw (402482) and stat
-
o
-
seal (S572) from manifold
-
handle (744303) hole #4 and bleeder hole on head
cylinder assembly (703119).
7.
In one continuous squeeze force oil into manifold
-
handle (744303) until oil starts to flow from bleeder hole on head cylinder
assembly (703119). While still squeezing the fill bottle (745263), use other hand to replace button head cap screw (402482) and
stat
-
o
-
seal (S572) on head cylinder assembly (703119) and torque to 35
-
40 inch lbs. (3.95
-
4.52 Nm). Do not over tighten.
This may require two people.
8.
Remove fill bottle (745263) and replace stat
-
o
-
seal (S572) and button head cap screw (402482) on manifold
-
handle assembly (744303)
hole #4 and torque to 35
-
40 inch lbs. (3.95
-
4.52 Nm). Do not over tighten.
9.
Proceed to bleeding instructions to remove air from hydraulic system.
Fill Bottle (745263)
Images may not reflect actual tool.
Oil passage with
o
’
ring (S832)
Power Cylinder (745331)
Top of Handle Assembly
***Keep air hole
free from oil***
Note:
•
Fill Bottle (745263) (sold separately) is required.
* FILLING & BLEEDING VIDEO AVAILABLE AT:
http://www.gagebilt.com/rivet_tools_videos.php
WARNING:
Do not cycle tool without air bleeder assembly (704153), or the screw and stat
-
o
-
seal, installed in tool head. Severe
personal injury could result.
WARNING:
Use CAUTION when removing screws, air bleeder assembly (704153) and fill bottle (745263). Hydraulic oil may be
under pressure.
CAUTION:
Before filling handle assembly (744129), air piston assembly (744121) must be all the way down.
CAUTION:
When forcing piston rod assembly (744136) downward, with head cylinder (703119) removed, hydraulic oil will eject forcibly
from handle assembly (744129).
CAUTION:
When bleeding tool, ensure tubing is free from kinks or other obstructions.
Hole marked #4 on Manifold
Handle (744303)
Bleeder Hole on Head Cylinder
assembly (703119) facing upward.
