background image

15

 

REV. 5/22

 

 

GB745SHV/LB8 INSTALLATION TOOL

 

SERIAL # 1001 AND ABOVE

 

 

REMOVING ACTUATOR ASSEMBLY

-

AIR (704130)

 

 

1.

 

Remove actuator lever assembly (704343) and pin

-

slotted (400608) from 

the handle

-

split (700326).

 

 

2.

 

Insert a 

5/8” 

open end wrench / adjustable wrench around actuator 

assembly

-

air (704130).

 

 

3.

 

Loosen the actuator assembly

-

air (704130).

 

 

4.

 

Remove wrench. Unthread and remove the actuator assembly

-

air (704130) 

 

with fingers from the handle

-

split (700326). 

 

INSTALLING ACTUATOR ASSEMBLY

-

AIR (704130) 

 

 

1.

 

Apply Teflon® tape onto threads of actuator assembly

-

air (704130) one to two 

wraps.

 

 

2.

 

Thread the actuator assembly

-

air (704130) all the way into handle

-

split (700326) 

with fingers.

 

 

3.

 

Insert and turn 

5/8” 

open end wrench / adjustable wrench and snug tight 

approximately 1/4

-

1/2 turn.

 

 

4.

   

Reattach actuator lever assembly (704343) and pin

-

slotted (400608) to the handle

-

 

 

split (700326). 

 

NOSE ASSEMBLY/ DISASSEMBLY

 

 

WARNING

Disconnect tool from its power source before actuator removal or installation. Severe personal injury may occur if 

 

power source is not disconnected.

 

 

 

CAUTION:  

Actuator assembly

-

air (704130) can break if not careful.

 

 

CAUTION:  

Do not over tighten actuator assembly

-

air (704130). Snug tighten only.

 

OVERHAUL

 

ACTUATOR ASSEMBLY

-

AIR

 

 

To assemble and disassemble nose assembly to tool, take the following steps:

 

 

   

1.  Disconnect air supply to tool.

 

 

 

 2.

 

 Loosen and removed connector (745503) then pull out insert (745355) 

   

 from rear of end cap (745332).

 

 

 

 3.

 

 Loosen and remove retaining nut stop (480125), retaining nut (480124) 

   

 and anvil holder assembly.

 

 

 

 4.

 

 Attach wrench to flats on collet and insert 

3/8” (9.5 

mm) Allen wrench 

   

(comes with tool) into hex in rear of piston (745310) and remove remaining 

   

 nose assembly parts (IE* collet, extension

-

collet & jaws). (Individual 

   

 parts vary depending on nose assembly).

 

 

 

 5.

 

 Assembly is the opposite of disassembly. Follow steps in reverse to 

   

 assemble your nose assembly. (See also nose assembly data sheet).

 

 

 

* Apply Vibra

-

tite® part # 405125 to all threads and allow it to set 20 

 

 

minutes prior to assembly.

 

 

   

* See overhaul pg. 17 for more information.

 

Images may not reflect actual tool.

 

Summary of Contents for GB745SHV/LB8

























Reviews: