Gage Bilt GB743VT Original Instructions Manual Download Page 24

Page: 24 / 24

REV. 4/22

GB743VT INSTALLATION TOOL

Riveter Kits Available

(Sold Separately)

Gage Bilt

offers a wide selection of standard and custom kits tailored to your needs.

Catcher Bag

Stem

#704214

(Sold Separately)

Air Bleeder Assembly

#704153

(Sold Separately)

Extensions

These extensions help reach many

restricted areas by increasing the overall

length of the nose assembly. They fit

directly on the GB743 Installation Tool.

(Sold Separately)

Part Number

Equivalent to:

2”

703002

743A50

4”

703004

6”

703006

TEFLON® IS REGISTERED TRADEMARK OF E.I. DUPONT DE NEMOURS & CO. LUBRIPLATE® IS A REGISTERED TRADEMARK OF FISKE BROTHERS REFINING CO. LOCTITE® IS A REGISTERED

TRADEMARK OF HENKEL CORPORATION. DEXRON® IS A REGISTERED TRADEMARK OF GENERAL MOTORS CORPORATION. SLIC

TITE® IS A REGISTERED TRADEMARK LA

CO INDUSTRIES.

GB743VT ACCESSORIES

Approved for use on Gage Bilt CE installation tools and/or other manufacturer

’

s CE approved tools of similar design.

(Sold Separately)

Tool Stroke Depth Gage

1935

(Sold Separately)

Approved

Image may not reflect actual gage

Summary of Contents for GB743VT

























Search results

Summary of Contents for GB743VT

Reviews:

Related manuals for GB743VT

Brands by name

Popular brands

Gage Bilt GB743VT, Original Instructions Manual

Search results

Summary of Contents for GB743VT

Reviews:

Related manuals for GB743VT

Brands by name

Popular brands