background image

6/11 Rev. 9/14 

GB704 S/N: 3213 AND ABOVE  

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. 

TABLE OF CONTENTS

 

Description

                                                                                                                             

Page

 

 

Warnings ................................................................................................................................................................... 3 

 

Principle of Operation ............................................................................................................................................. 4 

 

How to use the GB704 ............................................................................................................................................. 5 

 

Description, Operation and Maintenance .............................................................................................................. 6 

 

Filling, Bleeding and Troubleshooting .................................................................................................................. 7 

 

Overhaul, Disassembly and Parts Lists ........................................................................................................... 8-10 

 

DEXRON ® III Oil Safety Data ............................................................................................................................... 11 

 

Nose Assembly Selection Chart ........................................................................................................................... 12 

 

EU Conformity and Warranty ................................................................................................................................ 13 

SPECIFICATIONS

 

 

 

 

 

Hand Held Weight 

-   4.30 lbs. (1.95 kg) 

 

 

 

Air pressure req'd 

-   90-100 p.s.i. (6.2-6.9 bar) Max. 

 

 

 

Air consumption 

-   3.9 CFM at 20 Cycles a minute 

 

 

 

Hydraulic Oil 

-   Automatic Transmission Oil, 

 

 

  Dexron III, or equivalent. 

 

 

 

Setting stroke 

-   .540" (13.72 mm) 

 

 

 

Rated pull load 

-   3,300 lbs. (14.68 kN) 

 

Noise level 

-   81.5 dB (A)

 

 

                                 

Vibration   

-   Tested– No hazards found.  

 

 

 

 

Summary of Contents for GB704














Reviews: