GABRIEL KAKELUGNAR AVANTI G860 Assembly Instruction Manual Download Page 20 | Manualshive

Page: 20 / 28

background image

GABRIEL KERAMIK AB

20

IMPORTANT STEPS PRIOR TO TILING

• Mark the centre line (

Picture1

page 21)

• Check that the floor is level.

• Check the body surface. Is it vertical? Be aware that you must compensate for any
irregularities.

• All tiles must be level - vertically and horizontally.

• Adhesive shall be applied on

both tiles and body

with an 8 mm toothed trowel.

(

Picture2

page 21)

•  A joint width of approx. 3mm is recommended. The tiles are handmade with
  tolerance and joints could vary accordingly. The overall appearance is important.
  We recommend wooden wedges.

• Seal with adhesive between tiles and body around the firebox and the soot holes.

• Do not block the air inlet hole/grate for convection heat.

• Corner tiles are fixed to create a shadow line as shown (

Picture 3

page 21).

• Keep to the marked lines while tiling (

Picture 3

page 21).

• Be sure that the rear edge is straight towards the wall. (

Picture 3

page 21)

• Start tiling from the bottom centre and tile towards the sides.

• The tiles are hand-made - there might be some variations in measurements and colours.

Tiling and preparations

All manuals and user guides at all-guides.com

«
...
18
19
20
21
22
...
»

Summary of Contents for AVANTI G860





























Reviews:

No comments

Related manuals for AVANTI G860

Brand: United States Stove Company Pages: 20

Brand: Barmat Castings Pages: 10

Brand: United States Stove Pages: 60

Brand: Warm Tech Pages: 116

Brand: D'Alessandro Termomeccanica Pages: 29

MT. VERNON MTVERNON-AE-CSB

Brand: Quadra-Fire Pages: 24

Brand: Quadra-Fire Pages: 40

Brand: Hi-Flame Pages: 46

Brand: Heta Pages: 12

Brand: Heta Pages: 32

SCAN-LIINE 80 XL

Brand: Heta Pages: 28

Brand: Heta Pages: 26

Brand: Ventis Pages: 56

Brand: Coleman Pages: 1

Brand: Coleman Pages: 24

Brand: Coleman Pages: 24

Brand: Primus Pages: 8

Brand: Primus Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands