g-lites 56x3w Owner'S Manual Download Page 6

 

www.g-lites.com 

6. PHOTOMETRIC DATA 

PL5603CT

40° lens 

 

7. MOUNTING AND INSTALLATION 

Cautions: For added protection mount the fixtures in areas outside walking paths, 
seating areas, and away from areas were unauthorized personnel might reach 
the fixture. Before mounting the fixture to any surface, make sure that the 
installation area can hold a minimum point load of 10 times the device's weight. 
Fixture installation must always be secured with a secondary safety attachment, 
such as an appropriate safety cable. To avoid injury, never stand directly below 
the device when mounting, removing, or servicing the fixture. 
 
Mounting points: Overhead mounting requires extensive experience, including 
amongst others calculating working load limits, a fine knowledge of the 
installation material being used, and periodic safety inspection of all installation 
material and the fixture. If you lack these qualifications, do not attempt the 
installation yourself. Improper installation can result in bodily injury. Be sure to 
complete all rigging and installation procedures before connecting the main 
power cord to the appropriate wall outlet. 

 

Mounting: Our company is fully operational in any mounting position, hanging 

Summary of Contents for 56x3w


















Reviews: