background image

Original User Manual FUXTEC FX-GS36 

16 
 

12.

 

EC Declaration of Conformity 

-------------------------------------------------------------------------------------------

 

Herewith we, 
 
FUXTEC GmbH 
KAPPSTRASSE 69, 71083 HERRENBERG-GUELTSTEIN Germany 
 
declare that the product designated below 
 
GRIT SPREADER FX-GS36 (TTS80LB) 
 
To which this declaration refers, complies with the relevant essential health 
and  safety  requirements  of  the  applicable  EC  Directives  2006/42/EC.  This 
declaration refers only to the machine in which it was placed on the market; 
parts added and interventions carried out subsequently by the end-user are 
not considered. 
 
Applied harmonized standards: BS EN ISO 12100:2010 
 
EC type-examination certificate: 

GB/1067/3528/11-1 (CE), 

AVTECH  House,  Arkle  Avenue,  Stanley  Green  Trading  Estate,  SV93RW 
Handforth, Cheshire, UK 
 
 
Herrenberg, April 10, 2017 
 
Tim Gumprecht 
(Managing Partner) 

 

Manufacturer: 
 
FUXTEC GmbH 
KAPPSTRASSE 69, 71083 HERRENBERG-GÜLTSTEIN Germany 
Storage of the technical documentation: 
FUXTEC  GmbH,  KAPPSTRASSE  69,  71083  HERRENBERG-GÜLTSTEIN 
Germany

 

T. Zelic, Management 
 
 

Summary of Contents for FX-GS36


















Reviews: