FUTABA Big SkyLeaf Instruction Manual Download Page 5

5

D o  n o t  r e c h a r g e  a  b a t t e r y  t h a t  i s  d a m a g e d , 

deteriorated, leaking electrolyte, or wet. 

Do not allow the charger or battery to become wet. 

■  Do  not  use  the  charger  when  it  or  your  hands  are  wet.  Do  not 

use the charger in humid places.    

Do not short circuit the battery.  

 

Do  not  repair,  deform,  modify,  or  disassemble  the 

battery and/or battery charger.  

Do not drop the battery into a fire or bring it near a fire.

    

Do  not  charge  and  store  the  battery  in  direct  sunlight 

or other hot places.

     

Do  not  charge  the  battery  if  it  is  covered  with  any 

object as it may become very hot.

Do not use the battery in a combustible environment.

■ The gas could ignite ignite and cause an explosion or fire.  

Always charge the battery before each flying session.

■ If the battery goes dead during flight, the aircraft will crash.

Battery and charger handling precautions

DANGER

■ Charging  the  battery  past  the  specified  value  may  cause  a  fire, 

combustion, rupture, or liquid leakage. 

■ Do not charge the battery while riding in a vehicle. Vibration will 

prevent normal charging.

When  using  the  Lithium  battery,  do  not  connect  the 

charger  to  the  balance  charge  connector  and  the  power 
connector at the same time.

■ Doing  so  could  cause  a  fire,  combustion,  generation  of  heat, 

rupture, or liquid leakage.

Insert the power cord plug firmly into the receptacle up 

to its base.

Always use the charger with the specified power supply 

voltage.

■  Use  the  special  charger  by  connecting  it  to  a  proper  power 

outlet. 

If the battery liquid should get in your eyes, do not rub 

your eyes, but immediately wash them with tap water or 
other clean water and get treated by a doctor.

■ The liquid can cause blindness. 

Do not touch the charger and battery for any length of 

time during charging.  

■ Doing so may result in burns.

    

Do  not  use  a  charger  or  battery  that  has  been 

damaged.   

Do  not  touch  any  of  the  internal  components  of  the 

charger.

   

■ Doing so may cause electric shock or a burn.

  

If any abnormalities such as smoke or discoloration are 

noted with either the charger or the battery, remove the 
battery  from  the  transmitter  or  charger  and  disconnect 
the power cord plug and do not use the charger. 

■ Continued  use  may  cause  fire,  combustion,  generation  of  heat, 

or rupture.

Do not subject the batteries to impact.

■ Doing  so  may  cause  fire,  combustion,  generation  of  heat, 

rupture, or liquid leakage.

WARNING

Use  and  store  the  battery  and  battery  charger  in  a 

secure location away from children.

■ Not doing so may cause electric shock or injury.

If  the  battery  leaks  liquid  or  generates  an  abnormal 

odor, immediately move it to a safe place for disposal.

■ Not doing so may cause combustion. 

If  the  battery  liquid  gets  on  your  skin  or  clothing, 

immediately flush the area with tap water or other clean 
water.

■ Consult a doctor. The liquid can cause skin damage. 

After  the  specified  charging  time  has  elapsed,  end 

charging and disconnect the charger from the receptacle.

When recycling or disposing of the battery, isolate the 

terminals by covering them with tape.

■ Short circuit of the terminals may cause combustion, generation 

of heat or rupture.

Do  not  place  heavy  objects  on  top  of  the  battery  or 

charger.  Also,  do  not  place  the  battery  or  charger  in  any 
location where it could fall.

  

■ Doing so may cause damage or injury.  

Do not store or use the battery and charger where it is 

dusty or humid.

■ Insert  the  power  cord  plug  into  the  receptacle  only  after 

eliminating the dust.

After the aircraft/transmitter has been used for a long 

time, the battery may become hot. Immediately remove it 
from the aircraft/transmitter.

■ Not doing so may cause a burn.

CAUTION

Do not charge the battery in extreme temperatures.

■ Doing  so  will  degrade  the  battery  performance.  An  ambient 

temperature of 10℃ to 30℃  (50F to 86F) is ideal for charging.

Unplug the charger when not in use.

Do not bend or pull the cord unreasonably and do not 

place heavy objects on the cord.

■  The  power  cord  may  be  damaged  and  cause  combustion, 

generation of heat, or electric shock.

Summary of Contents for Big SkyLeaf

























Reviews: