Installation for OP20-48 (For SC-703, SC-1303/
ᆰɶዴᢿဇӕ˄Ậ
)
Turn the antenna upside-down, then carefully
cut the cable tie at the clamp indicated as“A”.
Unfasten the two screws on the cable clamp, then
remove the cable clamp.
For SC-703, also unfasten the two screws on the
cable cover, indicated as “B”, then remove the
cable cover.
ᆰɶዴᢿửᘻᡉẲềẆἃὊἨἽἁἻὅἩίᵟὸఌΨỉள
ዴἢὅἛửЏụộẴẇἃὊἨἽἁἻὅἩỉἊᵐஜửዼ
ỜềẆἃὊἨἽἁἻὅἩửӕụٳẲộẴẇ
ᵱᵡᵋᵕᵎᵑỉئӳỊẆἃὊἨἽỽἢὊίᵠὸỉἊᵐஜử
ዼỜềẆἃὊἨἽỽἢὊửٳẲộẴẇ
Unfasten and remove the nuts and bush at
“A”. For SC-703, also remove the cable
bush, indicated as “B”. These parts will be
reused. Next, remove the cable gland (C) by
pushing it with your finger.
ᵪᵟᵬἃὊἨἽỉఌΨỆẝỦẐἜἕἚᵏẑẐἨἕἉἷẑẐἜἕ
ἚᵐẑίᵟὸửٳẲộẴẇᵱᵡᵋᵕᵎᵑỉئӳỊẆẐἃὊἨἽ
ἨἕἉἷẑίᵠὸờٳẲộẴẇӕụٳẲẺᢿԼỊẆࢸỂẴ
Ổề̅ဇẲộẴẇẸỉࢸẆἃὊἨἽἂἻὅἛίᵡὸửਦ
ỂẲᡂỚẆٳẲộẴẇ
1
2
Unfasten the six screws on the base of the antenna (SC-703 has 11 screws), then turn the antenna right-side-up. Remove the
top cover. Disconnect the LAN cable from the PCB (indicated as“A”) and remove the cable gland and the gasket (indicated as
“B”, to be re-used). Pull the LAN cable out of the antenna, from the base.
For SC-703, remove the coaxial cable from the locking saddle (indicated as “C”) on the PCB cover.
ᆰɶዴᢿỉࡁᢿỆẝỦἊᵔஜίᵱᵡᵋᵕᵎᵑỉئӳỊᵏᵏஜὸửዼỜềẦỤᆰɶዴᢿửᘙỆᡉẲềẆᆰɶዴᢿỉỽἢὊửٳẲộẴẇؕெẦỤᵪᵟᵬἅ
ἁἑử৷ẟềίᵟὸẆᵪᵟᵬἃὊἨἽɥỉἃὊἨἽἂἻὅἛίᵠὸểἣἕỿὅᵆᵠᵇờٳẲộẴίࢸỂ̅ဇὸẇᆰɶዴᢿỉࡁᢿẦỤᵪᵟᵬἃὊἨἽửࡽẨ৷Ẩ
ộẴẇᵱᵡᵋᵕᵎᵑỉئӳẆؕெỽἢὊɥỆẝỦἿἕỿὅἂὁỶἶἇἛἽίᵡὸẦỤӷ᠆ἃὊἨἽửٳẲộẴẇ
3
Unfasten the four screws on the PCB cover, then remove the PCB cover. Fit the locking saddle (”A”, included) to the PCB.
ؕெỽἢὊỉӕ˄ẬἊᵒஜử
ٳẲềẆؕெỽἢὊửӕụٳẲộ
ẴẇؕெỆἿἕỿὅἂỺἕἊἇἛ
ἽίᵟẆӷὸửӕ˄ẬộẴẇ
4
SC-703
SC-1303
SC-703
SC-1303
B
A
A
A
B
C
A
A
A
B
C
