Turn the antenna unit upside-down, then
re-fit the nuts and bush removed at step 2 to
the location on the antenna base indicated as
“A”. (Recommended torque: 0.76
N•m).
For SC-703, fit the cable bush (indicated as “B”)
to the indent in the antenna base. Next, replace
the cable cover removed at step 1.
ᆰɶዴᢿửᘻᡉẲềẆᵐỂٳẲẺẐἜἕἚᵐẑẐἨἕ
ἉἷẑẐἜἕἚᵏẑίᵟὸửӕụ˄ẬộẴίዸ˄ἚἽἁᾉ
ᵎᵌᵕᵔᵬᶋὸẇ
ᵱᵡᵋᵕᵎᵑỉئӳỊẆẐἃὊἨἽἨἕἉἷẑίᵠὸửἃὊἨἽỽἢὊỉЏụഎẨˮፗỆӕ˄ẬộẴẇẸỉẝểẆᾀỂٳẲẺἃὊἨἽỽἢὊửΨỆ
ẲộẴẇ
9
Turn the antenna unit right-side-up, and attach the cable bush to both connector end of the LAN cable, then between the LAN
COAX CONV KIT and the PCB (indicated as “A”). Loop the excess LAN cable twice , then secure the LAN cable to the
coaxial cable with a cable tie (indicated as “B”) at the lower location than the LAN COAX CONV KIT. Secure the LAN cable to the
two cable clamps (“C”).
For SC-703, secure the cable for both antennas to the locking saddle indicated as “D”.
ᆰɶዴᢿửᘙỆᡉẲẆᵪᵟᵬἃὊἨἽኵԼίӷὸỉἅἁἑɲᇢỆἃὊἨἽἨἕἉἷửӕụ˄ẬẺẝểẆؕெểẸỉɥỆӕụ˄ẬẺᵪᵟᵬᵽᵡᵬᵴኵԼ
ỆዓẲộẴίᵟὸẇᵪᵟᵬἃὊἨἽỉ˷ЎễᧈẰỊᵐࠇẨỆẲềẆᵪᵟᵬ٭੭ỿἕἚợụ˯ẟˮፗỂẆӷ᠆ἃὊἨἽểσỆளዴἢὅἛίӷὸỂܭ
ẲộẴίᵠὸẇộẺẆᵪᵟᵬἃὊἨἽỊளዴἢὅἛử̅ẾềἃὊἨἽἁἻὅἩᵐίᵡὸỆܭẲộẴẇ
ᵱᵡᵋᵕᵎᵑỉئӳỊẆᵐếỉỴὅἘἜẦỤỉἃὊἨἽửẆἿἕỿὅἂὁỶἶἇἛἽίᵢὸỆܭẲộẴẇ
11
Pass the cable through the cable clamp (indicated as “A”), then fasten the
cable clamp. Secure the cable to the cable clamp at the location indicated
as “B” with a cable tie, then cut any excess cable tie.
ἃὊἨἽἁἻὅἩίᵟᵇỆἃὊἨἽửᡫẲẆἃὊἨἽἁἻὅἩỂܭẲộẴẇ
ἃὊἨἽἁἻὅἩểἃὊἨἽửẆளዴἢὅἛίӷὸỂܭẲộẴẇளዴἢὅἛ
ỉ˷ЎễᧈẰίᵠὸỊЏụộẴẇ
10
ᵑỂٳẲẺᆰɶዴᢿỉỽἢὊửӕụ˄ẬộẴẇ
Re-fit and secure the cover removed at step 3.
12
SC-703
SC-1303
B
A
A
B
A
For SC-703
Pub. No. C72-01601-C
(1905, REFU) OP20-47/48
Note:
Take care not to crush the anti-fall cord between the antenna cover and base.
දᵇᴾẮỉểẨẆᆰɶዴᢿỽἢὊỆếẟềẟỦӵɦậኜửẆਬộễẟợạỆẲềẪẻẰẟẇ
A
A
B
D
C
䢲䢲䢲䢳䢻䢴䢶䢳䢵䢳䢴
